Log in

View Full Version : beaterX project thread

Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 [29] 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152
NOT THE BLUE LAMPSHADE
07-05-2010, 10:05 PM
I snapped a pic when I got home thursday, I couldn't believe my eyes!

http://www.scheides.com/albums/evoX-clutch/IMG_2897.sized.jpg

I'm guessing some dust covers were left off?
scheides
07-06-2010, 08:35 AM
I'm guessing some dust covers were left off?

For this pic, yes. I mean literally this pic was taken after the trans was bolted back up to the block. Once we got everything back together, yes, the dust covers and every little other thing we took off during the tear-down was put back in place :)
scheides
07-07-2010, 01:39 PM
Check out this sweet plate that Rosey machined for me! I'm going to get it powdercoated over at primo sometime in the near future.

http://www.scheides.com/albums/evoX/IMG_1337.sized.jpg
goodhart
07-07-2010, 01:41 PM
Any before picture? I don't wanna scroll through 14 pages. :D
turbotalon1g
07-07-2010, 01:43 PM
Looks great that guy's got some skills.
scheides
07-07-2010, 01:49 PM
Any before picture? I don't wanna scroll through 14 pages. :D

IDK if I have any. It was just a black piece of plastic with 3x holes like the center one. When I got the seat heater controls in there they obviously didn't fit, and a few attempts I made with bondo were nothing short of amazingly aweful. Rosey made this piece and then shaved down the entire top 1/4" of the black plastic, this fits right on top. Once its PC'd It'll get affixed to the plastic piece below with a little bit of our favorite bonding agent :D
scheides
07-07-2010, 01:51 PM
Like this:
http://www.scheides.com/albums/evoX/IMG_2539.sized.jpg

But with round pegs in the two outside square holes :D
Matt D.
07-07-2010, 01:52 PM
Check out this sweet plate that Rosey machined for me! I'm going to get it powdercoated over at primo sometime in the near future.

The button on the left is crooked. :)
goodhart
07-07-2010, 01:54 PM
Looks good man! Rosey's got some skillz

The button on the left is crooked.

Cause scheides does the gangsta lean!
Kracka
07-07-2010, 01:57 PM
The 2008 GSR came stock with a coin tray in that location. The 2008/10 MR and 2010 GSR came with the single AWC button as pictured above.

Example of coin tray:
http://www.evoxforums.com/forums/attachment.php?attachmentid=3218&d=1236706089