91 Galant VR4

[Swifty1638]

I've never been on his nuts lol.

[URV8SUX]

Keep up the good work John get this thing going!

[Pushit2.0]

Cash money is about all I need to finish this build. Here are the update pics, and this will be it for a while. I will be storing the car for a few months, just until I have the cash to finish the project, then it will be reassemble with some minor touch up here and there.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_19005.jpg

Here is the flat black dash.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_19006.jpg

I added a 1/4" thick aluminum washer to the rear cross member mount plates.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_19001.jpg

Here is the down pipe and twin tial 38mm waist gates plumed back into the exhaust, the other one will be mounted over the alternator.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_19004.jpg

Here is the almost completed engine bay shot.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_19002.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_19003.jpg

I added aluminum hold down/together straps for the water to air intercooler.

~John

[scheides]

Crazy hot! Can't wait to see this thing rollin :D

[turbotalon1g]

Gawd Ver. 2.oh no is looking great.

Keep up the hard work a lot of people are happy for you and excited to see this on the road.

[Pushit2.0]

The car runs, it would have fired right up but I forgot to mark which coil was what, so after 10min of poking it starts and cams at 1400rpm on E-85 with an old map I had converted to 550cc primary injectors and E-85.

Now for the bad news, to make a long story short I was trying to get the car on the dyno and up to the MAP shoot out this weekend. But the Evo 3 3rd and 4th gears I bought for the home made Stage 4 tranny are on national back order and I will not have them for a few weeks.

I would ask to buy or borrow a tranny or just the gears from a tranny but I think I can wait a little longer for my parts to show up. So for now here is a small look at what we have been up to for the past 2 months.

http://www.mitsustyle.com/photopost/data/612/medium/Picture_20049.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20048.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20051.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20056.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20055.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20059.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20054.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20052.jpg
http://www.mitsustyle.com/photopost/data/612/medium/Picture_20050.jpg

Here is a run down of the new shinny parts:

- Tranny, everything to make a stage 4 tranny: evo 3 1st gear, cut double syncro 2nd, evo 3 3rd and 4th gear conversion, new bearings threw out, welded center diff, welded parts on the front diff you help keep it in 1 piece, new shift forks, new magnetic drain plugs, new throw out fork and throw out bearing, etc

- Quarter master twin disk clutch

- Tial 38mm WG with 1.6bar springs x2

-Tial 50mm bov

-A1000 fuel pump, filters, and FPR

-PTE 550s primary and ford 1600cc secondary injectors

-civic 1/2 sized radiator

-17" wide Kirkey race seat and 5 point harness for the passanger side

-A ton of electrical stuff to make everything work

-BF goodrich T/A drag radials 225 50 15's this should give me a 9.2" contact patch at all 4 corners

-etc

So I hope to get it down the track this season yet, but as the title goes on the galantvr4.org post, the never ending project.

~John

[Halon]

Looks great!!! Interesting how you mounted the coils.

[Swifty1638]

Is this what you called about?! What can I do to help?

[santa]

How come the wastegate's are not at the collector?

[Speedfreak]

How come the wastegate's are not at the collector?

It's a divided housing, but yeah, I guess it would still be doable down there.