Beater 2g

[C3L1CA]

Quarter master said my clutch is pretty much toast and that they could sell me a new one for $2,158. Then told me about a new twin disc they're coming out with and how it should be pretty cool.

I then I just asked if any of it is salvagable enough to make a run out of it. Then told him I want to try and get the record back for trap speed on a stock block. His attitude seemed to change a bit from the whole thing being junk to maybe being able to salvage something. He said he'll check with his guy again and see if they could throw something together. It'd be pretty bad ass if I could even get used broken shit that is less broken than mine.

Here's to bugging people enough and hoping that I can get a pass or two in this year. Hopefully get out of my doomed 140 traps.

[santa]

Quarter master said my clutch is pretty much toast and that they could sell me a new one for $2,158. Then told me about a new twin disc they're coming out with and how it should be pretty cool.

I then I just asked if any of it is salvagable enough to make a run out of it. Then told him I want to try and get the record back for trap speed on a stock block. His attitude seemed to change a bit from the whole thing being junk to maybe being able to salvage something. He said he'll check with his guy again and see if they could throw something together. It'd be pretty bad ass if I could even get used broken shit that is less broken than mine.

Here's to bugging people enough and hoping that I can get a pass or two in this year. Hopefully get out of my doomed 140 traps.

That would be pretty cool of them! Good luck with getting it going again!!!

[C3L1CA]

The only thing that was still salvagable was one floater plate :( Hmmm maybe time to go auto :(

[goodhart]

Hmmm maybe time to go auto :(

Do it.

[C3L1CA]

I haven't completely given up yet.

Picked up an auto 98 gsx that has a spun rod bearing.

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs464.ash2/73767_609292451282_40103751_35184316_6072413_n.jpg

Probably swap in the auto stuff into my beater, swap what remaining 5 speed stuff I have into this red car and buy a tranny, t-case and use it as a daily driver.

Might make another thread for the 98 when it gets going and I start working on it. Woop woop for having something to do to my car again. Can't decide to try and salvage the 7 bolt, try and get the extra 7 bolt going he is giving me, or rebuild the 6 bolt I have in the garage, or put in my muchgsx stage 2 motor and build a new motor for the beater. Argh, somebody make up my mind for me.

[19TsiAwd90]

put you muchgsx stage 2 in this and build a new better motor lol

[C3L1CA]

That might be the way to go, I just want to get it going so I can sell of my Audi that I am using as a daily and put that towards auto goodies or a motor. I do kinda want to go after the et record on a stock motor though since I'm now taking out most of the driver skill

[goodhart]

That might be the way to go, I just want to get it going so I can sell of my Audi that I am using as a daily and put that towards auto goodies or a motor. I do kinda want to go after the et record on a stock motor though since I'm now taking out most of the driver skill


It'll be close :)

http://mitsustyle.com/forums/showthread.php?t=28295

It would be pretty sweet to have a local hold the record though, you have the trap speed for it.

[turbotalon1g]

Keep the munchgsx motor, obviously these noobs have no clue about it.

Plus now that you are auto, it should be easier to get the record well at least you hope it will be.

Go get that record!!

[C3L1CA]

This should be the last full day with the dsm. It's been fun and I have learned more than I ever thought I would have with this thing.

http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0717.jpg

http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0718.jpg

http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0719.jpg

Shit is tuckin pretty good ;)
http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0721.jpg
^What happens when an axle on my other dsm was stuck in the hub, this car had a good hub/axles, and having no junk tires until the next day.

http://i6.photobucket.com/albums/y202/C3L1CA/IMG_0725.jpg

Had some good times with it..

http://www.youtube.com/watch?v=7KdZnFBNmQ8

http://www.youtube.com/watch?v=fjdNPd7k9vI&feature=related


Oh well, time to move on to a less rusty more than just a tin can dsm.

Thanks for the space!