the evo 3 swap parts are coming

[TkrPerformance]

Got the 2nd tial on the way for the manifold and will be running 1600cc and e-85 now the new chip for the car showed up the other day. Just need a few more thingsfor the new set up. Hope I can get it all done by the cook out

[TkrPerformance]

worked on the car the last 2 days
got the tranny filled back up with redline heavy weight shock. and the hella horns put on yesterday.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01032.jpg

today dad and I got the manifold all fixed up. made a new coil bracket so it will bolt were the a/c bracket was. welded in the 10an bung to the extra oil pan I had. got the dnp manifold and the pte5031e off the car after we started the car up with no down pipe to check out the clutch and it is 100 times better than the QM was.

bye to the dnp,pte5031e
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01028.jpg
pipes and flex for the new down pipe
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01027.jpg
10an bung (on a 100 year lease :))
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01029.jpg
the top mount
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01031.jpg
the huge housing that is not getting used 1.34
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01030.jpg
does clear with the hood on with the 1.34 housing with a few inch's
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01026.jpg
10an drain tube. it is a 4000psi oil,hydro hose with crimp on 10an ends.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01033.jpg

[123abc]

Wow! This is going to be sick.

[Kevin 1G Drummer]

Hmm, that hose and the fittings look very familiar... Why is this? haha

[TkrPerformance]

I have no idea why it looks familiar ;)

[TkrPerformance]

dad and I worked on the car today. craig and kevin also came by for some beer's

got the griffin scirroco radiator fitted. just have to cut off the water neck and have it welded shut and cut the upper hose fitting and have it come out at a 45 so it will clear the turbo better. Also cut out the full top radiator surport to make room for the radiator so we made a nice flat bar to bolt in and has a 90 piece of steel in on the bottom to hold the top of the radiator.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01041.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01042.jpg

we put in a 2g upper motor mount that we had to mod it to fit with the polly mount
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01045.jpg

got both of the tial 38's on the manifold
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01043.jpg

also picked up a set of hood pins from craig. need to use them now since the car will no longer have a hood latch on it because the radiator is now sitting there.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01048.jpg

[awd-drifter]

that evo is gonna be sick Mark. lookin sweeet man.

[TkrPerformance]

got the radiator and water neck back from John(Pushit2.0) to day. big thanks to him for welding them up. Had the upper hose pipe welded at a 45 and the radiator cap cut off and welded shut. On the water neck it is the evo III bottom and a 1g upper and it is also at a diffrent angle so it will clear the turbo when it get's back I hope soon so I can get the car done.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01054.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01055.jpg
water neck
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01052.jpg
also put in the other evo III water pipe I had since I dont need to run the dented pipe any more. Also show's the new angle for the water neck
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01053.jpg

Dad worked on the radiator. cut some holes in the mounting tabs to install the oem rubber mounts for the radiator and welded in a set of bolts to hold the bottom of the radiator.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01056.jpg
the new upper radiator support. We made it a bolt in so the radiator can be taken out with out taking the top mount off the car. It also holds the front and back of the top of the radiator so it does not move at all.
http://i122.photobucket.com/albums/o280/tkrperformance/evo/DSC01057.jpg

[sleepydsm]

A lot of work! Looks fun! So are you gonna just use a chip for this car?

[TkrPerformance]

just the chip for now with the safc2. that is all that has been out there for the car. unless I want to run aem or power fc.
But dsmlink just got done with the firm ware for the evo I-III ecu so I will be switching it over soon