PDA

View Full Version : Finally getting stuff done on our cars

Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 [58] 59 60 61 62 63 64 65 66 67
Pushit2.0
08-16-2007, 10:15 AM
I think a set of Weld wheels(or similar, light) and full slicks will be in order befor it sees the track.

~John
Pushit2.0
10-05-2007, 11:41 AM
I have a little more done on the car, radiator and hoses are almost done, the wiring is almost done, and I decided to remove the dash and make a custom gauge cluster. I have cut down the alternator harness to where I need it, now its time to run the wires for it. I hope to have it at the fall dyno day. The car will be tuned on E85 or c-16, it depends when MN switchs to the winter mix.

~John
Goat Blower
10-05-2007, 12:28 PM
I have a little more done on the car, radiator and hoses are almost done, the wiring is almost done, and I decided to remove the dash and make a custom gauge cluster. I have cut down the alternator harness to where I need it, now its time to run the wires for it. I hope to have it at the fall dyno day. The car will be tuned on E85 or c-16, it depends when MN switchs to the winter mix.

~John

Bah, use E98, much cheaper and the blend is consistent.

Good to see you're keeping it and getting her done.
turbotalon1g
10-05-2007, 12:35 PM
^second that, keep it buddy, its cool that you have had that car since HS, don't give it up and if you ever need a hand after hours let me know.
niterydr
10-05-2007, 12:43 PM
I have a little more done on the car, radiator and hoses are almost done, the wiring is almost done, and I decided to remove the dash and make a custom gauge cluster. I have cut down the alternator harness to where I need it, now its time to run the wires for it. I hope to have it at the fall dyno day. The car will be tuned on E85 or c-16, it depends when MN switchs to the winter mix.

~John

Lies.

C-16 noob.
Pushit2.0
10-05-2007, 12:52 PM
I am running on hopes and dreams, and I might have to push it across the line.

~John
Swifty1638
10-05-2007, 12:56 PM
not was a 2jz no shyt!!!

-A. Swift
Pushit2.0
10-05-2007, 12:59 PM
"after 10, 15 grand tops, over night parts from Japan if we have to, it will desimate all." "I need 2 big bottles, and I need it by tonight", the only time in the hole move they referd to it has Nitrous Oxide, not nawwwzzzz.

~John
niterydr
10-05-2007, 01:42 PM
Shouldn't you guys be working somewhere?

(I am on hold transfering a call!).
Swifty1638
10-05-2007, 03:23 PM
Nope. I jsut got back from the shop. Thanks john! I think every issue is fixed! It pulls, shifts through the gears when I pound them, doesn't die on me..etc. Too bad the end of the year is here, and If I tuned it would be a waste. So, I'll wait till I get those parts we talked about onto my car, then tune. I think this time around the clutch will hold, and the car will rev out!

-A. Swift