PDA

View Full Version : Progress since last year

Pages : 1 2 3 4 5 6 [7] 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
santa
03-08-2010, 06:19 PM
Spoke with Justin today from pte, he told me to get the .58ar T4 again if I want a massive powerband. It will make the power I want and flow very well. the.58 T4 is slightly bigger then a T3 .81. So, I bought the 6765 with a ported shroud H cover with a .58 T4 exhaust housing. :) Should be here next week.
Swifty1638
03-08-2010, 06:23 PM
Damn..small again! Go you!! I assume open t4?
santa
03-08-2010, 06:26 PM
Damn..small again! Go you!! I assume open t4?

Yes, its a T4 if you take a look at the dyno graph on the most recent map evo 2.3 build it made over 800awhp on a t3 .81 which Justin from pte said is slightly smaller then a T4.58. So I went with that housing selection. If I'm not happy I'll just swap housings :)

http://mitsustyle.com/forums/showthread.php?t=25571
goodhart
03-08-2010, 07:28 PM
Yes, its a T4 if you take a look at the dyno graph on the most recent map evo 2.3 build it made over 800awhp on a t3 .81 which Justin from pte said is slightly smaller then a T4.58. So I went with that housing selection. If I'm not happy I'll just swap housings :)

http://mitsustyle.com/forums/showthread.php?t=25571



I think he was wondering if it was an open T4, or a divided housing T4.
Shane@DBPerformance
03-08-2010, 07:30 PM
I have made over 800 Dynojet awhp numbers with the 6765 and a little T3 .63 A/R. The T4 .58 should do the job.
santa
03-09-2010, 01:19 AM
I have made over 800 Dynojet awhp numbers with the 6765 and a little T3 .63 A/R. The T4 .58 should do the job.

Wohoo! I was trying to get your attention!! I think the .58 is gonna make that turbo hit real hard! Do you think my old style tial 38mm gate will control it ok?
Swifty1638
03-09-2010, 01:20 AM
Yes. I'm using same wg on my turbo. Only thing it won't do well is LOW boost, but any real person doesn't run that, so no worries! ;)
tehehodi
03-09-2010, 01:29 AM
Schweet! i hope you post up more pics of progress
santa
03-09-2010, 02:32 AM
Schweet! i hope you post up more pics of progress

I will post more shortly!! :)
Shane@DBPerformance
03-09-2010, 09:34 AM
Wohoo! I was trying to get your attention!! I think the .58 is gonna make that turbo hit real hard! Do you think my old style tial 38mm gate will control it ok?

Worst case with the exhaust housing, you just buy a .68 T4 for $200.

The 38mm might be able to control it, depends on the exhaust manifold design and WG placement. If you are only going to run highish boost anyways, then it should be fine. The problem is when people try to run them on pump gas with a questionable WG design/location and they end up creeping to 25psi or whatever above 7000RPMs.