More About My Engine

**JET** · 11-11-2003

Well, I sold the pistons out of my engine because I am building a 2.4L from scratch. I was pulling the rods out and noticed that Rick mixed up 2 of the rod caps! They are numbered and 2 of them were switched around!! That is always a great thing to see. If you want it done right, you have to do it yourself!

I will give QPR a shot too, because I know and trust those guys too. Well, maybe not Allan!! :stick:

AJ · 11-11-2003

Quote:

Originally posted by JET@Nov 11 2003, 07:03 PM

I will give QPR a shot too, because I know and trust those guys too. Well, maybe not Allan!! :stick:

Hey now, every good shop needs a good tool bitch!

Jana · 11-11-2003

Everyone starts somewhere...and hey, at least he hooked my turbo up correctly

**JET** · 11-11-2003

Just givin' ya shit AJ!!

AJ · 11-11-2003

I think most people realize I am not going in with Mike and Josh for my Die hard tuning knowledge or engine building background. Oh I will bust my ass to learn and improve on what I do know, But we each have our backgrounds and areas that will benifit the shop.

But back to the topic, That sucks to hear JET, but hopefully yhat 2.4 will just fucking rock!

AJ · 11-11-2003

Quote:

Originally posted by JET@Nov 11 2003, 08:43 PM
Just givin' ya shit AJ!!

I know, It's all good. :smoker: +

+ me = fun behind a welder!!!!

Enes · 11-11-2003

as long as you stay behind the welder and don't spill any

in it we all will be fine

Raptor · 11-11-2003

Thanks for the comments JET and we are looking forward to checking out the 2.4 when you are done.

Hey Allan, get me a torque wrench biatch!

J/K Allan is an asset to the shop in many ways and for the areas he needs experience in, I don't expect it will take long for him to be fully up to speed. We all have our stronger areas, it is turning out to be a very good mix.

**Shane@DBPerformance** · 11-11-2003

What kind of rods were they?

**JET** · 11-12-2003

They are Eagle rods. I am going to have them resized and use them in my 2.4L. I have heard some bad things about the Eagles not being perfectly round. With the HP I plan on making I am almost tempted to sell the Eagles and get some Crowers.

Then if I am going to buy rods, then I could go with the longer rods and get the better rod ratio out of them, but then the wrist pin is in the bottom ring of the piston. I am still up in the air a little bit, but I am pretty sure I will just use the Eagles and new Wiseco's.

niterydr · 11-12-2003

Quote:

Originally posted by JET@Nov 12 2003, 12:40 AM
They are Eagle rods. I am going to have them resized and use them in my 2.4L. I have heard some bad things about the Eagles not being perfectly round. With the HP I plan on making I am almost tempted to sell the Eagles and get some Crowers.

Then if I am going to buy rods, then I could go with the longer rods and get the better rod ratio out of them, but then the wrist pin is in the bottom ring of the piston. I am still up in the air a little bit, but I am pretty sure I will just use the Eagles and new Wiseco's.

didn't know weisco made rods

.
For the dsm's there are three equally good options, light, heavy, and heavier (eagle, crower, and pauter). I think the eagle incorperate I beam, while the other two use H (or is it the other way around), I originally chose the eagles because they are lighter than the other two options and cheaper AND rotating mass is a bad thing. And to the best of my knowledge no-one has broken any of them due to shear power, maybe its best to stick with what you have.
What brand rod does marco use for his motors?
thanx for the shout out jet btw

.

**1ViciousGSX** · 11-12-2003

Quote:

Originally posted by niterydr+Nov 12 2003, 12:23 PM--></div><table border='0' align='center' width='95%' cellpadding='3' cellspacing='1'><tr><td>QUOTE (niterydr @ Nov 12 2003, 12:23 PM)</td></tr><tr><td id='QUOTE'> <!--QuoteBegin-JET@Nov 12 2003, 12:40 AM
They are Eagle rods.  I am going to have them resized and use them in my 2.4L.  I have heard some bad things about the Eagles not being perfectly round.  With the HP I plan on making I am almost tempted to sell the Eagles and get some Crowers.

Then if I am going to buy rods, then I could go with the longer rods and get the better rod ratio out of them, but then the wrist pin is in the bottom ring of the piston.  I am still up in the air a little bit, but I am pretty sure I will just use the Eagles and new Wiseco's.

didn't know weisco made rods

.
For the dsm's there are three equally good options, light, heavy, and heavier (eagle, crower, and pauter). I think the eagle incorperate I beam, while the other two use H (or is it the other way around), I originally chose the eagles because they are lighter than the other two options and cheaper AND rotating mass is a bad thing. And to the best of my knowledge no-one has broken any of them due to shear power, maybe its best to stick with what you have.
What brand rod does marco use for his motors?
thanx for the shout out jet btw

. [/b][/quote]
Pauter.
Marco lightens them on the stage 4 motors. That's what he's doing with mine, including the pistons and crank.

santa · 11-12-2003

Jet didnt one of your oil squirters brake off of your old motor? Just curious I heard that from a friend of mine.

niterydr · 11-12-2003

thanks vicious, I thought thats what he used, but I wasn't sure, and I hate giving false information (I talked to him about strokers along long time ago).

**JET** · 11-12-2003

I actually forgot to check the oil squirter, but I will take a look at it now that the rods are out of the way.

**Goat Blower** · 11-13-2003

Quote:

Originally posted by JET@Nov 11 2003, 07:03 PM
I was pulling the rods out and noticed that Rick mixed up 2 of the rod caps! They are numbered and 2 of them were switched around!!

Yeah, that could be a bit of a problem. Even though they have some quality issues for not having the journals sized correctly, the cap and rod would be matched from the factory. An honest mistake, but one that shouldn't have happened. Have them resized and reuse them.