after 10 years its coming back to life

[TkrPerformance]

picked up a head gasket from spaz yesterday and got the head on. Also clocked the evo 3 turbo and had to cut the bolt out of the o2 housing since I could not get both nuts on the bolts with the down pipe on. Just used a new bolt since the flange was slotted to start with and was able to use the stock nuts to bolt it all up with the help of spaz.
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03922.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03923.jpg
It is the first time in 10 years the car has had a full engine and tranny in it :) It is getting closer

[Goat Blower]

Looking good. I have to pull my visors apart as well when I put in a suede headliner in the GSX this winter.

[cmspaz]

If by "with the help of spaz" you mean I held a wrench on a bolt that wasn't spinning anyway, then yes, I helped. :D

[Sparky2211]

Looks good so far!

[TkrPerformance]

It is getting cold out now. I worked on it a little bit today. got the a/c pump on,alt on, put power steering back in the car. also rebuilt the tial waste gate and made a j pipe.
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03924.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03925.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03926.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03928.jpg

[turbotalon1g]

Nice, your 16G is facing the wrong way. lol

[TkrPerformance]

yes it is facing the wrong way now, but looks a lot better with out a big j-pipe and the stock wastegate on it

[portum89]

i think i saw this whole project live lol

[TkrPerformance]

Dad came by today and we put the timing belt on the car. Also put the cas and rail/injectors on to seal the rest of the engine up till I get a intake manifold. and got the lower piping all hooked up
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/IMG_20111118_162953.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/IMG_20111118_163010.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/IMG_20111118_163001.jpg

also put the winter tires and rims on the hatch so it is ready to go now
http://i122.photobucket.com/albums/o280/tkrperformance/IMG_20111118_163527.jpg

[TkrPerformance]

Been working out in the cold the last 2 days. I got a new rear bumper on the car now I found at the junk yard. it has no holes in it like the old one. It was cheaper to buy this one over me fixing the old one on the car. also picked up a heat shield for 5.00 local. The evo 3 intake manifold and coil bracket showed up picked it up for 75.00 shipped since I sold the 2 that I had years ago.
What I got done. timing cover is on all pullys and belts are on the car. got the oil cooler mounted and -an lines on the ofh to the oil cooler. Got the evo 3 intake on, all the wiring is on. Just have to make the harness for the 94 cas.
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03930.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03931.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03932.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03935.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03933.jpg
http://i122.photobucket.com/albums/o280/tkrperformance/awd%20spyder/DSC03934.jpg