MitsuStyle MitsuStyle

Go Back   MitsuStyle > The Classifieds > Mitsu vehicle parts for sale

Reply
 
Thread Tools Display Modes
Old 08-02-2010   #1
MustGoFaster
 
MustGoFaster's Avatar
 
Yeti Long Shot: Porpoheus Champion!
Join Date: Oct 2003
Location: Usa
Drives: A big dirty V8
Posts: 2,239
Send a message via ICQ to MustGoFaster Send a message via AIM to MustGoFaster Send a message via Yahoo to MustGoFaster Send a message via Skype™ to MustGoFaster
FS: All my Mitsu/ 3S stuff

For Sale: all my 3S stuff.

Built 6G72 short block: Pauter rods, Wisco pistons .060 over, stock forged crank, machined 4 bolt block, balanced assembly, ready to assemble. $2000 as is, $2500 assembled

Billet oil pump gears. Made by Boostaddict $400 – new never used.
http://www.3si.org/forum/f4/bfg-s-badas ... uy-439745/

Stock 5 speed 25 spline trans. Needs a rebuild and the mid case replaced. I have a replacement mid case that is included. $500

5 speed 25 spline T-case with Quadco input spool and EK2 t-case brace. $500

5 speed 25 spline T-case, input splines ok but not new. $150

CUSTOM 5 speed 25 spline trans and 6 speed t-case. These two are a matched pair, will not separate.
Custom you ask? It's been modified to be the shortest gearing possible in a 3S. It has been modified to allow a 6 speed t-case bolt to the 5 speed trans. After that it uses a JDM 6 speed front ring and pinion and needs the 5 speed rear diff to match it. The net result is the shortest gears possible for a 3S. Why would you want short gears? Mostly for autocrossing. If you are interested and want more details, here's a link: This trans also has a Quadco output shaft and a Kormex front differential. Unfortunately it needs the ½ hub and slider replaced along with 2nd gear and the syncro too. Shifts fine otherwise. $1500 obo

AEM EMS with 5 bar map and GM AIT. Tentatively sold

880cc injectors $200

13T's, non-robbeck, WG mounts are kind of iffy. Sold

Stock 3.0L with 130K on it. New oil pump, water pump, t-belt and pulleys, 3G HLA's(lifters) and valve stem seals 10K ago. Great oil pressure. Sale Pending

NA VICS manifold and a custom built box that allows the AEM EMS to control it. $100

IC setup with 12x24x4.5” PTE core, custom endtanks, and custom short route IC pipes. 2” hot side 2.5” cold side. It will probably not work on a car with A/C and you will need to redo the power steering cooler. Solid motor mounts required as well (included). Will not work with stock fans. Tial
50mm BOV included. $1300

Walbro 255 Sold

SCE Oil pan – 4 bolt - $Sold

Stock TT axles. $50 each, multiple rear sets, one front set.

Window regulators- re-enforced, won't break again. $100 per side.

Fuel Lab AFPR, -6 ports PN: 51502-1 Black Brand new never used! $120
__________________
Actual Women

Last edited by MustGoFaster; 08-18-2010 at 05:31 PM..
MustGoFaster is offline   Reply With Quote
Old 08-18-2010   #2
MustGoFaster
 
MustGoFaster's Avatar
 
Yeti Long Shot: Porpoheus Champion!
Join Date: Oct 2003
Location: Usa
Drives: A big dirty V8
Posts: 2,239
Send a message via ICQ to MustGoFaster Send a message via AIM to MustGoFaster Send a message via Yahoo to MustGoFaster Send a message via Skype™ to MustGoFaster
Re: FS: All my Mitsu/ 3S stuff

Sold parts updated.
__________________
Actual Women
MustGoFaster is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 07:06 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.