So here's the story. My 7bolt spun a bearing so I was putting a 6bolt together but I just don't have the time to deal with DSMs anymore. After selling off the shell these are the remaining parts I have left.
Sorry for the bad pics, I don't have a digital camera so everything's taken with my camera phone.
1G DSMLink (950s chip) -
sold
http://i242.photobucket.com/albums/f...g_dsmlink1.jpg
http://i242.photobucket.com/albums/f...g_dsmlink2.jpg
2G DSMLink (850s chip) -
sold
http://i242.photobucket.com/albums/f...g_dsmlink1.jpg
http://i242.photobucket.com/albums/f...g_dsmlink2.jpg
6bolt bare block. Has oil squirters. It was bored .020 over and hot tanked by Motors by Gosh. Should be ready to go in a new build. -
$200
http://i242.photobucket.com/albums/f...olt_block1.jpg
http://i242.photobucket.com/albums/f...olt_block2.jpg
http://i242.photobucket.com/albums/f...olt_block3.jpg
6bolt virgin crank. Journals are still within spec and it's been micropolished. -
$150
http://i242.photobucket.com/albums/f...olt_crank1.jpg
http://i242.photobucket.com/albums/f...olt_crank2.jpg
http://i242.photobucket.com/albums/f...olt_crank3.jpg
6bolt cut crank. Rod journals are in spec, mains are cut .010 as seen in the 3rd pic. -
$100
http://i242.photobucket.com/albums/f..._cutcrank1.jpg
http://i242.photobucket.com/albums/f..._cutcrank2.jpg
http://i242.photobucket.com/albums/f..._cutcrank3.jpg
1g head. Cleaned and blasted by Motors by Gosh. Stock vavles cleaned and lapped. Stock springs and retainers. Stock cams. No lifters. -
$200
http://i242.photobucket.com/albums/f...bolt_head1.jpg
http://i242.photobucket.com/albums/f...bolt_head2.jpg
6bolt 8.3CR Wiseco pistions .020 overbore. New and never used except to mock up the engine. -
sold
http://i242.photobucket.com/albums/f...rts/wiseco.jpg
6bolt Eagle Rods. New and never used except to mock up the engine. -
sold
http://i242.photobucket.com/albums/f...eco_eagles.jpg
6bolt ACL Race main bearings standard size. New and never used except to mock up the engine. -
sold
http://i242.photobucket.com/albums/f...nbearings1.jpg
http://i242.photobucket.com/albums/f...nbearings2.jpg
6bolt ACL Race rod bearings standard size. New and never used except to mock up the engine. -
sold
Sorry no pics.
6bolt ARP head studs. New and never used except to mock up the engine. -
sold
Sorry no pics.
6bolt ARP main studs. New and never used except to mock up the engine. -
sold
ACT2900 and ACT lightweight flywheel. Used for 1500 miles. -
$300
http://i242.photobucket.com/albums/f...0flywheel1.jpg
http://i242.photobucket.com/albums/f.../2900_disk.jpg
http://i242.photobucket.com/albums/f...p_flywheel.jpg
2g Fluidyne aluminum radiator with slimeline fans. -
$250
http://i242.photobucket.com/albums/f..._fluidyne1.jpg
http://i242.photobucket.com/albums/f..._fluidyne2.jpg
Cast T3 manifold with external wastegate flange. New. -
$200
http://i242.photobucket.com/albums/f...st_t3mani1.jpg
http://i242.photobucket.com/albums/f...st_t3mani2.jpg
SBR cast 2g manifold with external wastegate flange. Used for <5k miles. -
$200
http://i242.photobucket.com/albums/f...sbr2gmani1.jpg
http://i242.photobucket.com/albums/f...sbr2gmani2.jpg
Tial 38mm Silver external wastegate. Used for <5k miles. -
$150
http://i242.photobucket.com/albums/f...rts/tial38.jpg
FIC 850cc Injectors. Used for <5k miles. -
$200
http://i242.photobucket.com/albums/f.../FIC_850s1.jpg
http://i242.photobucket.com/albums/f.../FIC_850s2.jpg
http://i242.photobucket.com/albums/f.../FIC_850s3.jpg
FIC Aeromotive AFPR kit. Used for <5k miles. -
sold
http://i242.photobucket.com/albums/f.../AFPR_kit1.jpg
http://i242.photobucket.com/albums/f.../AFPR_kit2.jpg
2G Generic FMIC kit. Street Imports core (smaller one). JCWhitney mandrel bends. Dejon upper intercooler pipe. Turbo XS blowoff valve. Used for 20k
miles -
$150
http://i242.photobucket.com/albums/f.../FMIC_kit1.jpg
http://i242.photobucket.com/albums/f.../FMIC_kit2.jpg
http://i242.photobucket.com/albums/f.../FMIC_kit3.jpg
2G SSAC FMIC kit. New never used. -
$250
Sorry no pics. You can find the pics on Ebay though.
Mitsubishi complete gasket kit. New never used -
sold
http://i242.photobucket.com/albums/f...asket_kit1.jpg
http://i242.photobucket.com/albums/f...asket_kit2.jpg
2G AWD exhaust system. 2.5" RnR aluminized 02 eliminator to 3" Thermal R&D exhaust. Used for 20k miles. -
$150
http://i242.photobucket.com/albums/f...m_thermal1.jpg
http://i242.photobucket.com/albums/f...m_thermal2.jpg
That's it for now. I do have other stock 2g parts laying around, like 2g starter and plate, 2g alternator, 2g water pump, 2g front case and they're all in good condition. Feel free to stop by to take a look at any of the stuff. Thanks.