4g63tcrazy's new setup for 2010 - Page 10

sleepydsm · 04-10-2010

Dang, I should have looked at those when I was at their place!

4g63tcrazy · 04-11-2010

^^ I need rims more then you do!

I need to find out what size tire to run/ if I need a spacer. I wont have a problem in the rear like AWD guys do. But I still have to clear the front struts. I have a little more than 1/4" of space between the back of the rim and strut right now. A 10mm spacer might be needed if I want some meaty tires.

sleepydsm · 04-11-2010

I NEED RIMS MORE! I have crappy 2gB GSX wheels

Boo hiss. But I'm cheap and the roads here suck so maybe I shouldn't get a nicer set?

I was looking at my engine bay, and because of you I really want to take it all apart and re-do everything... hahaha. Your harness is awesome. I like that your changed where it enters the engine bay. So you gonna be at the Dyno Days?

turbotalon1g · 04-11-2010

Nice pickup, I like them from a performance standby, but I haven't quite seen them look good on a DSM.

haha kevin new sig. U must of been that guy cruising 65 in the lambo back in the day.

4g63tcrazy · 04-11-2010

Quote:

Originally Posted by sleepydsm

I NEED RIMS MORE! I have crappy 2gB GSX wheels

Boo hiss. But I'm cheap and the roads here suck so maybe I shouldn't get a nicer set?

I was looking at my engine bay, and because of you I really want to take it all apart and re-do everything... hahaha. Your harness is awesome. I like that your changed where it enters the engine bay. So you gonna be at the Dyno Days?

Your wheels look really good on your car. Not to mention you have some sticky tires on them. Since your car is down right now it would be a good time for you to clean it up a little more! I'm kinda glad this happened cause now I have all this time to do the things that have always kinda bothered me. Not to mention I was 12k miles overdue for a timing belt!!

And yes I'll be at the dyno day at MAP. Probably the one at DB too.

Quote:

Originally Posted by turbotalon1g

Nice pickup, I like them from a performance standby, but I haven't quite seen them look good on a DSM.

haha kevin new sig. U must of been that guy cruising 65 in the lambo back in the day.

I'll try and make them look good.

LOL at his sig. I saw that yesterday.

santa · 04-12-2010

I've had fd wheels on my car for 4 years now. tire size is 225 50 16 and they barrly clear the rear strut. You also have to notch the rear forward angled lower control arm even with spacers on them or else the wheels will rub. I made 530awhp last year and hooked up pretty good with 225's.

4g63tcrazy · 04-12-2010

Quote:

Originally Posted by santa

I've had fd wheels on my car for 4 years now. tire size is 225 50 16 and they barrly clear the rear strut. You also have to notch the rear forward angled lower control arm even with spacers on them or else the wheels will rub. I made 530awhp last year and hooked up pretty good with 225's.

FWD

I'm curious about your clearance in the front though. How much room do you have between the tire and strut?

Right now I'm either going with 235/55r16 or I might go all out with spacers, extended studs and some really fat tires. Not sure!

4g63tcrazy · 04-12-2010

Great news! Somehow I got best of both worlds! FAT tire and no need for spacers.

I ended up putting on 245/50r16's. I only have 2 on right now cause my work didn't have the others in stock. Those will get put on tomorrow. I think these wheels look SICK. I'm really excited to get the car down on all 4 and see how it looks! On to the pics!

(don't mind the thick layer of dust on the car

)

LOOK AT THAT CLEARANCE!!

Less then a mm and it does not rub. I will be taking the hammer to the perch though to give me added comfort.

9" of tire-assfault traction goodness!

Swifty1638 · 04-12-2010

typical women..on the phone.

4g63tcrazy · 04-12-2010

I know right? And she thinks my new wheel setup is ugly..

Swifty1638 · 04-12-2010

eeeh..I don't think they are the best looking wheels out there, but they do serve their purpose. Tell her if they are ugly, then she can buy you some nice 16x8-8.5" wide Kosei's, Volks, Works, etc. I am sure she'd shut it then.

4g63tcrazy · 04-12-2010

Haha or some RPF1's

Kevin 1G Drummer · 04-12-2010

That's actually only about 8" of contact patch

Nice setup, but I've never really cared for the way FD wheels look.

4g63tcrazy · 04-13-2010

Close enough to 9 for me! Ha

sleepydsm · 04-13-2010

I think they will look pretty good

**goodhart** · 04-13-2010

Are those Falken Ziex ZE-912's ?

4g63tcrazy · 04-13-2010

Yes they are.

**goodhart** · 04-13-2010

Quote:

Originally Posted by 4g63tcrazy

Yes they are.

I hope you get traction with those. I had them on my car when I was FWD for a while and they sucked bad. No traction till at least 3rd gear.

123abc · 04-13-2010

Quote:

Originally Posted by goodhart

I hope you get traction with those. I had them on my car when I was FWD for a while and they sucked bad. No traction till at least 3rd gear.

Thats pretty normal for a fwd dsm... lol

4g63tcrazy · 04-13-2010

Haha very true! Well I work at Tires Plus and these tires have the softest sidewalls for a performance tire. (That we carry.) All the others are stiff for cornering. They have a AA traction rating too. Either way I'll get more traction then I had before with low profile tires and 18" rims.

Update time.. Since I had the day off I installed the other 2 tires. Then I took them home and prepped the rims for paint. Ideally I would have painted the rims with the tires off but I can't have my car on jackstands taking up space. I ended up doing 3 coats of semi-gloss black and 2 coats of clear. They turned out pretty nice. While I was waiting for the paint to dry, I installed my fuse box and wired up my fans. I wired my fans up like stock for now. If that doesn't do the trick I'll add a switch later. I also took a hammer to the spring perch. Now I have 1/4" of clearance.

Here are a couple pics I took before I painted the rims.