89 colt turbo part out

[6pucker]

im taking apart the car this weekend so parts and shell wont be available until then. chassis might have to be put back together by purchaser. just the front bumper though
original 89 dodge colt turbo(same as mirage)
*chassis*
white
paint is not faded but has stains
little to no rust
220xxx miles
has some suspension mods(kyb shocks and some sort of rear sway bar)
shell is pretty clean if not the cleanest in mn. asking $1000 for shell.

evo 3 16g with 2g ported exhaust manifold with less then 150 miles $300 *sold* thanks
brand new aftermarket stock location super bling'n j-pipe $20
brand new o2 housing with external dump $40
brand new southbend dxd dual friction clutch $185
brand new mitsubishi timing belt in unopened package $30
6bolt head with 3rd gen lifters + resurface $200 *sold*
1g intake manifold with qpr block off plates $15
2g intake elbow $10
barely used greddy type s bov $125 obo *sold* thanks
1g upic hardpipe $30 (i think its a dejon pipe, also barely used)
used and cut 1g pacesetter 3 in dp $15
1g refreshed 6bolt block with new bearings, oil pump, water pump, crank pulley and all new timing components $225 *sold*
91 1g eprom ecu $115

thanks for looking and my number is 651-329-8881 ask for sia

will be adding more

[CarRacer]

Interested in the turbo. Where is the car located? I'm assuming no shaft play with that mileage? What diameter is the j pipe?

[TkrPerformance]

Willing to sell the shocks and springs. I do have a oem set could give you with some cash

[Halon]

Where are you located? And does the car still have the rear calipers on there? I'm looking for the banjo conversion fitting that is on the rear calipers.

[6pucker]

Originally Posted by CarRacer

Interested in the turbo. Where is the car located? I'm assuming no shaft play with that mileage? What diameter is the j pipe?

the car is located in the maplewood, oakdale area. the turbo has no shaft play. im not sure on the diameter of the j pipe but i do know that it is bigger then the stock pipe, i wanna say 1.5-1.75 in?

Originally Posted by TkrPerformance

Willing to sell the shocks and springs. I do have a oem set could give you with some cash

Originally Posted by Halon

Where are you located? And does the car still have the rear calipers on there? I'm looking for the banjo conversion fitting that is on the rear calipers.

sorry guys but i dont want to split up the shell. sorry if the title is a little misleading. just parting out motor and selling shell as a whole.

[6pucker]

bump for new parts and prices

[TkrPerformance]

If you want to part with the suspention let me know. I have the stock suspention in mine and cash for the set up you got. I would be willing to swap them over also

[TkrPerformance]

If you want to part with the suspention let me know. I have the stock suspention in mine and cash for the set up you got. I would be willing to swap them over also

[6pucker]

Originally Posted by TkrPerformance

If you want to part with the suspention let me know. I have the stock suspention in mine and cash for the set up you got. I would be willing to swap them over also

sorry tkr i dont want to mess with the shell at all. just wanna sell as a shell. thanks

[6pucker]

bump for eprom ecu

[6pucker]

bump for new rock bottom prices

[daneatsv8s]

Hey, this is Dan. I texted you a few days back about the block. Can you tell me more about the block? Did it come off a running car? Were the piston rings replaced? What brand were the water pump/timing belt components? I'm very interested and could pick it up tonight or tomorrow for 200.00 cash.

Call me back or PM me back: 612 - 381- 6195

Thanks - Dan

[johnson]

You got an alternator? I got $20 on it!

[6pucker]

sorry johnson no alternator.

[6pucker]

shell is ready to go!