Race Galant VR4 for sale.... $10,000 OBO or part out.

[Pushit2.0]

I was building this car to run 8s at some point. It would only take a few weekends of work to finish this car. The body is in fare shape a little rust around the window, a few dings here and there. The interior is stripped right now, and has a 8point roll cage in it(would be certified for an 8.50@150mph. I have the full interior and a lot of extras. I also did not plan on running any kind of lights, head lights or tail lights so you would need to wire those back in, this was going to be a series race car. The chassis has just over 100k on it and here is the VIN: JA3CX56U0MZ010883 and I would also part the car out if that would work better. Here is the link to the gallery with most of the pics:
http://lseperformance.com/gallery/ma...g2_itemId=3231
I will get a few more pics up of the rest of the car tonight.

Here is the new list of for sale items.

LSE stage 4 short block (2.0L still), 40 over 9.25:1 Weisco pistons, Crower rods, ARP mains, LSE main cap pins, no oil squirters, new TB side w/ Greddy timing belt
-LSE stage 6 head, race port head, 2mm over I/E SS valves, Crower 415s, Crower cam gearsn
-Cometic HP head gasket
-A1 L-19 head studs
Running engine $5000 obo

-ACT street light flywheel $120 obo

-Custom south bend race only clutch (single disk design) $300 obo

-3bolt ring/pinion 4bolt rear end combo $250 obo

-water to air IC setup, with a custom side mount heat exchanger, intake air temp was only 10deg above outside air temp at 47psi..... with no ice in the water tank. $650 obo

-AEM EMS for tuning, AEM 5bar MAP, GM AIT sensor, 93 CAS (pending sale)

-Full MSD ignition, DIS 2, GM twin post coils, MSD wires $450 obo

http://img443.imageshack.us/my.php?i...sc02371it9.jpg
http://img443.imageshack.us/my.php?i...sc02370uq8.jpg
http://img443.imageshack.us/img443/5...2369bk9.th.jpg

The hole car as it sits: $7,000 OBO

I just do not have the budget to finish and maintain the car, I wish I did, but not right now. Email: GalantVR41062@yahoo.com, PM, Phone:7634254340. Thanks for looking!

~John

[DSM_421]

I call the downpipe if you part it!

[GREASEMONKEY]

If it gets parted out i will defiantly take a couple things off your hands

[bluntedelvis]

WTF, why are you parting this out? But if you are parting, dude hook me up!!! you know what I need.

[DSM_421]

I'd be interested in the 22spline aluminium T case if you end up parting.

[iceminion]

How is the shell? is it worth saving? If so I might be interested in the shell

[Pushit2.0]

I do not think the shell is that great.

~John

[Pushit2.0]

Items I would like to sell.

-Ford 1600cc injectors, like new 20 miles on them $make offer (pending sale)

-Water to Air inter cooler setup, 3" in and out with lines pump and heat exchanger. Intake air temps at 47psi with an outside air temp of 55deg was 65deg. $make offer

-SMIM, custom made should perform like the AMS VSR, 90mm TB flange coated black with some heat exchanging stuff (pending sale)

-4" down pipe $make offer

-Greddy Type R BOV with HD spring -Sold-

-4 bolt rear end, with 3 bolt ring and pinion, GVR4 housing so you could install AWS $make offer

-AEM EMS with 5bar MAP and AIT sensors and pig tails (pending sale)

-South Bend clutch sprung 6 puck FE disk and 2900+lb PP, feels like a 2100. $make offer

PM with offers, thanks.

~John

[FattyBoomBatty]

I sent a couple PM's your way, please let me know about that!

[Pushit2.0]

Got back to you, sorry about the wait.

[Super Bleeder!!]

Who bought the turbo?

[Pushit2.0]

That's a good question.

[Pushit2.0]

Update

[turbotalon1g]

Hey thats a DXD-F right?

[Pushit2.0]

2900lb PP, 6 puck sprung FE disk. So the PP is a little harder then the DXD and it has a sprung 6 puck for quick engagement/disengagement (faster shifting). I could drive it as a DD clutch and it will not weld to the flywheel/PP.

~John

[Pushit2.0]

Update again, any other questions?

~John

[blackrosenova400]

How much do you want for the msd wires?

[blackrosenova400]

Also how much for the aem setup if you havent sold it

[blageo23]

How much for the head without cams and cam gears? Also what kind of springs are in there?

[Pushit2.0]

PM's sent.

~John