|
Possible spyder partout?
Possible chance of partout due to going back to school and getting out of debt. Seeing if there is any interest in these parts and how much you guys will pay. Almost all parts have 0 miles. Yes, 0 miles. 30 minutes of idling time is all it had on the motor and parts.
Engine: 6 bolt 4g63 turbo block -.020 Ross pistons -Eagle rods with ARP bolts -standard OEM crank -Clevite 77 bearings -ARP headstuds -Oil pump(not sure if OEM) -BSE kit 1g head Venom Intake manifold Rebuilt non-turbo throttle body with FIAV deleted 3g lifters BC 280 cams BC valve springs and retainers New OEM 6 bolt timing belt kit New OEM water pump New OEM 90 oil filter housing ARP mainstuds Cometic head gasket Forced Performance Exhaust Manifold Stud & Nut Kit Non-cruise control cable Jay's racing alternator relocation kit New OEM Lower timing belt cover(GVR4) 6 bolt swap harness New OEM Thermostat New OEM Thermostat gasket New OEM Engine mount bolt New OEM DSM Oil Dipstick Tube CXracing 19 row oil cooler Black Prothane motor mounts Echelon (2) -8 AN male to male fitting Echelon (2) -8 AN swivel hose end fitting 90 Degree Echelon (2) -8 AN swivel hose end fitting straight 6ft Russell Proclassic -8an line Ebay o2 dump housing (2)Aeroquip FBM5243 - Aeroquip AN to Metric Adapter Fittings Auto Meter 2269 - Auto Meter Metric Adapters Auto Meter 3224 - Auto Meter Tubing and Line Kits Earl s Performance 991101ERL - Earl's Performance Couplers Earl s Performance 991701ERL - Earl's Performance Tee Adapter Fittings Bosche spark plug wires New OEM lower radiator hose New OEM 2g Coolant temp sensor HKS cam gears JMF coil pack relocation Zaklee Clear cam gear cover Magnus heat barrier intake manifold gasket OEM throttle body gasket CAS billet polished cover Q45 throttle body HKS timing belt OEM Coil Pack HKS clear cam gear cover Rebuilt non-turbo throttle body Front Line Fab -10AN oil catch catch Valve cover with 1/2 NPT fittings Water pipe with -16AN fitting Thermostat housing with -16AN fitting Drivetrain: FWD transmission B&M short shifter New OEM transmission bell housing bolts Competition Clutch stage 4(6 puck ceramic) New OEM Flywheel inspection plate New OEM Starter plate New OEM Clutch cylinder reservoir New OEM Clutch cylinder reservoir bracket New OEM Transmission mount bolt New OEM Transmission mount nut New OEM Rear mount bolt New OEM Rear mount nut New OEM Front mount bolt New OEM Front mount nut New OEM Fulcrum clutch pivot bolt New OEM Clutch release fork NEW OEM DSM Clutch Release Fork Boot New OEM shift cable bracket MD747231 New OEM transmission mount to plate MF140270 (2) New OEM shifter cable bolts MF241255 (2) New OEM rear transmission mount bolts MF241308 (3) Extremepsi Complete SS clutch line Energy Suspension Shifter Base Bushing Kit Mitsubishi Extended Pushrod Brass underhood shifter cable bushing New OEM Shifter base plate MR176810 New OEM Axle nut MB109029 New OEM Axle washer MB109025 New OEM Cable clips MB367526 New OEM transmission mount nut New OEM Axle cotter pin New OEM Axles seals AWD driveshaft and exhaust hangers Turbo system: Borg warner S200 FP Race turbo manifold JMF FP race manifold heat shield Ebay 3" piping 4" intercooler kit ARP turbo bolts ARP o2 housing bolts 7cm turbo to manifold gasket Echelon -10 AN/Russel Proclassic turbo oil drain (2)Oil return flange -10an fitting Turbo drain flange -10an fitting Garrett/BEP/Turbonetics T3/T4 Turbo Oil Drain Gasket New OEM oil pan return gasket Intercooler support bar OEM EVO 3 02 housing gasket OEM O2 housing stud Tial Q 50mm BOV purple HKS purple velocity stack 3" aluminum pipe with Tial flange O2 housing dump Thermal R&D 3" exhaust K&N filter Fuel: New OEM Fuel filter Bosche 1680cc low impendence injectors MAP SS braid Fuel feed line kit Electronic: DSMlink v3 ECMlink socket service Input buffer 95 Eprom ECU AEM Wideband AEM Truboost New OEM knock sensor Speed density harness GM IAT sensor IAT bung GM 3 bar map sensor Suspension: H&R 15mm spacers H&R extended wheel studs KYB GR2 shocks with ebay coilovers New OEM (6)Top strut mount bolts New OEM (2)Suspension fork bolt New OEM (2)Suspension fork nut Wheels: 17x10+18 Enkei RPF1 Brakes: AEM 4 piston and 12" rotors Wilwood 4 piston rear caliper New OEM Master cylinder reservoir New OEM Master cylinder reservoir bracket New OEM Brake crush washer MA111832 New OEM Brake Line clips MA431825 Exterior: Used black 2g OEM fenders RM front lip EDM tail lights Interior: Nardi deep corn Evo X shift knob |
Re: Possible spyder partout?
|
Re: Possible spyder partout?
Sad sad sad. Are you keeping the car itself then?
|
Re: Possible spyder partout?
Yikes! That's way too nice to get parted!
|
Re: Possible spyder partout?
That's a shame, must be panda sale time.
|
Re: Possible spyder partout?
That engine bay is gorgeous!
|
Re: Possible spyder partout?
The whole car is gorgeous*
|
Re: Possible spyder partout?
Who knows what's gonna happen. If there's enough interest, the part out will happen. If not, I'll still be happy. It can go different ways. Maybe I'll keep the shell and years from now I'll build a high revving aluminum rod setup? Or else jump on the evo x bandwagon?
|
Re: Possible spyder partout?
Spppfff..Evo X. This has and always will have bad ass written all over it. You've done it up perfect.
|
Re: Possible spyder partout?
I will slap you. Its not costing you a dime to let it sit for a while!
|
Re: Possible spyder partout?
I've already slapped myself a couple time just starting this thread. But I've gotta get back in school. I can't build gm transfer cases and driveshafts my whole life.
|
Re: Possible spyder partout?
School doesn't always equal awesome high paying job
|
Re: Possible spyder partout?
Dibs on wheels and edm tails just sayin lol if it does happen.
I say keep it it is way to nice to part out like everyone else says |
Re: Possible spyder partout?
Yeah I would love those EDM tails as well
|
Re: Possible spyder partout?
Quote:
|
Re: Possible spyder partout?
Right now there is not too much interest. I would possibly like the engine sold first. Unless someone wants to buy the whole thing. Or maybe if nobody shows interest then it won't get parted out.
|
Re: Possible spyder partout?
Ill give you my stock tails plus money for those edm ones i would also like that lip and wheels like i said above lol
|
Re: Possible spyder partout?
Quote:
Good luck, but for the time and money into the car, I'd say just sit on it or sell something else if you have to. |
Re: Possible spyder partout?
So maybe it is a good thing i didnt go to school for cars.
|
Re: Possible spyder partout?
just switch work places. try to find a place that is fun to work. Maybe a local "race shop" is looking for a good mechanic to help build cars.
I find for myself - work on "projects" is always more fun then "ruitine" work over and over again. |
| All times are GMT -5. The time now is 10:37 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.