how to learn engine building???

[Shane@DBPerformance]

There might be some videos out there now on engine building. Even though they would be for V8s, most of the same methods apply. You would want a factory manual for the motor you are rebuilding also to get all the specs and weird things specific to that motor.

[Raptor]

That is true, I have seen a few videos available online for it. Probably a good idea either way since you could watch it more than once and ask your questions online after without the fear of some annoyed engine builder smacking you with a heavy object.

[Enes]

This is why I like this site more than anything, for the smart answers and good politeness!

[Matt D.]

without the fear of some annoyed engine builder smacking you with a heavy object.
Namely a 7-bolt crankshaft.

I have yet to build my own engine, but even disassembling an engine you learn how it's assembled and where the pieces go. It's a puzzle, except there are specific measurements that need to be followed for nearly every part.

[Enes]

If you want it done right, pay someone to do it and it will last longer.

When I end up building my engine I will work it into the deal that when the engine is being put together that i am present and watching, even if it means i have to pay extra for the priviledge/time I would not even think about it and gladly would pay.

[520Talon]

If you want it done right, pay someone to do it and it will last longer.

When I end up building my engine I will work it into the deal that when the engine is being put together that i am present and watching, even if it means i have to pay extra for the priviledge/time I would not even think about it and gladly would pay.


Wise words, unless you are planning on building a bunch of motors and don't mind having the car down for a while. I have put a couple together and at the first 1000 pan pull to see how its going I have found barring shavings and had to redo it again. Fourtunately I have never had a massive failure, but I only drive the car a few times a year and enjoy the building as much as the driving.

P.S. The current motor was not built by me because it gets tiresome doing it over, and over, and over.

The answer to your question is I just did it armed with a hanes and a chilton and all the internet reading I could find. Even with all of that the first one I put together and turned over puked coolant all over the place from between the head and the block. 2G headstuds (on a 1G) will torque down to spec on the bottom of the bolt holes while the head still has 2mm of gap. Ahh, the memories.

[white 2g awd]

You better not be being a smartass kid or you will find your stay here a short one. Ask a educated question and you will get a educated answer, and this means typing so we can read what the hell you mean without getting a fucking headache.
Yes, and I sent DSMStyle a pm with an apology for this. Everyone else, thank you for your insight, it is much appreciated.

[white 2g awd]

After just reading through all the replies, I think I agree too. My only problem though is I just don't have the money, I miss my car. My car has been sitting in the driveway since last august. But none the less i'm going to go to DMACC (Des Moines Area Community College) on thursday and see if I will have enough time for classes, considering I have two jobs that i have to keep, and maybe three here soon. I guess my only worry is pulling the engine, and putting it back, then not forgetting to hook something up, and ruin the motor.
This is why I like this site more than anything, for the smart answers and good politeness!
Yes this is why I posted here. Because of all the dsm sites I am a member of, this one has had the nicest and most knowledgeable people so far. I posted here because I respect alot of you for being so nice and helpful.

[niterydr]

That is true, I have seen a few videos available online for it. Probably a good idea either way since you could watch it more than once and ask your questions online after without the fear of some annoyed engine builder smacking you with a heavy object.

LMAO!!
Like mentioned, some knowledge is to be had from classroom and other various froms of instructions, but the majority of the population on this board is from hands on experience.

[Pimpin Dsmstyle]

That is true, I have seen a few videos available online for it. Probably a good idea either way since you could watch it more than once and ask your questions online after without the fear of some annoyed engine builder smacking you with a heavy object.

.....haha that is a very true risk.. mikes a bitch like that ;) Glad to have you back.