Log in

View Full Version : Built 2G DSM Part Out (35R, big brakes, Shep trans, etc.)

Pages : 1 [2] 3 4 5
DavidPHumes
08-13-2012, 09:30 AM
Picture of the compressor wheel. I don't think you can actually notice it, and maybe it doesn't even matter but in the interest of full disclosure...

http://i90.photobucket.com/albums/k265/David343/CompressoreWheel.jpg?t=1344868217
DavidPHumes
08-13-2012, 02:58 PM
Make offers. The worst I can say is no. For purchases above $200, I can deliver in the Twin Cities metro or equidistant from Duluth.
DavidPHumes
08-14-2012, 12:46 PM
Sale pending on the roller with transmission, the fuel system, and the turbo.
G4G63SX
08-16-2012, 09:55 PM
Interested in the wideband and link. Will the dsmlink work in a 1G sense you had a 6 bolt in there or is it for a 2G harness?
C3L1CA
08-17-2012, 08:36 AM
I'm pretty sure link is 1g or 2g specific.

You parting out any of the interior? I'd be interested in the center vent if you are.
DavidPHumes
08-17-2012, 08:55 AM
Interested in the wideband and link. Will the dsmlink work in a 1G sense you had a 6 bolt in there or is it for a 2G harness?Link is gen specific, but the wideband is still available. Let me know.
I'm pretty sure link is 1g or 2g specific.

You parting out any of the interior? I'd be interested in the center vent if you are.I don't think so for now, I'm going to try to sell the car as a roller. I'll let you know if that changes.
DavidPHumes
08-17-2012, 08:17 PM
Magnus sold, DSM link sold, injectors sold, fuel rail sold.

I will update the OP and start adding pictures of individual parts.
Speedfreak
08-17-2012, 10:27 PM
How many miles, and whats the condition of the tranny? How does it shift? Any idea of what was done to it?

Off the top of my head I can't remember if a 2g tranny will fit in an 1g?
DavidPHumes
08-17-2012, 10:42 PM
How many miles, and whats the condition of the tranny? How does it shift? Any idea of what was done to it?

Off the top of my head I can't remember if a 2g tranny will fit in an 1g?I'll scan in the build sheet tomorrow, but about 10,000 miles on it and it shifts mint. I had a problem with reverse when I stopped driving the car but that ended up being the shift linkage fortunately. Never grinds. It's always had Redline in it.

I'm not sure about fitment in a 1G.

Updated OP with some part specific pictures.

Edit: uploaded build sheet for Shep trans
punxnotdead185
08-18-2012, 02:14 PM
How many miles, and whats the condition of the tranny? How does it shift? Any idea of what was done to it?

Off the top of my head I can't remember if a 2g tranny will fit in an 1g?
Being this car is a 2GB and not a 2GA a tranny swap between generations is a little more difficult. You will for sure need the 2GB transfer case with the 2GB transmission being that they changed the final drive in the trans in 97 and instead of changing the rear end ratio to match they made up the difference by changing the gear ratio in the transfer case. And I believe you need both the 2GB starter plate and possibly the bracket for the shifter cables. It is not a direct swap but it can be done if you get all the associated parts to go with it. Do some research and you should be able to find out what you need Dave to include with it so it'll work.