Project 2G GSX

[Sparky2211]

I have lurked here for some time, but never really got around to posting. I've been out of the car game for some time now and finally feel that it is time to finish my 2G. I bought this from Matt D. some time ago, but with 70+hrs/week work and full load finishing up my bachelors/certs I just lost interest. Over the last month I have accumulated quite a few parts to get this finished. Below is the list so far.

1997 Eclipse GSX

Block:
- 2.0L MAP 6-bolt
- Eagle Rods
- Ross Pistons
- MAP Ultimate H11 Headstuds
- Fel-Pro PermaTorqueMLS Head gasket
- Gates Timing Belt
- ACL Rod Bearings
- ACL Main Bearings

Head:
- 1G MAP Stage 3 Cylinder Head
- Ferrea Valve Guides
- Ferrea valve seals
- GSC Springs, Retainers, seats
- MAP +1mm Nitride Valves
- HKS 280 Cams

Fuel:
- FIC 1680cc BlueMAX High Impedence Injectors
- Walbro 255 Fuel pump
- AEM Fuel Pressure Regulator
- Turbosmart FPR Liquid Fill Gauge
- AEM Fuel Rail

Intake/Exhaust/Turbo:
- ETS 10.5" Race Intercooler Kit
- PTE GT3561 turbo
- Magnus Race Intake Manifold
- DNP Turbo Manifold
- Apexi turbo-back
- Accufab F75 5.0L 75mm Throttle Body
- Tial 44mm Wastegate
- Tial Q Blow Off Valve
- MAP 44mm O2 Housing
- Greddy Trust Boost Controller
- MAP 3" Intake/filter

Drivetrain:
- TRE rebuilt transmission
- Competition Clutch Stage 4
- ACT Lightweight Flywheel
- Prothane Motor Mount Inserts
- Techna-Fit Clutch Line
- Prothane Motor Mount Inserts

Electronics:
- AEM AIT Sensor
- AEM 5-Bar MAP
- Eprom ECU w/DSMLink V3
- GM 3" MAF Sensor
- Prosport Peak/Hold Boost Guage
- Prosport Peak/Hold Oil Pressure Gauge
- Prosport Peak/Hold Wideband Guage

Suspension/Wheels:
- Koni 5-way adjustable shocks
- H&R race springs
- ADR 17x7 wheels

Misc:
- Mishimoto Aluminum Radiator
- Mishimoto 12” Electric Fan
- Taylor Battery Relocation kit


I guess now I am looking for advice. What else do I need or should get? I am trying to do it right the first time so I don't run into problems down the road. My goal has always been 600AWHP, but will be happy with whatever this produces.

[turbotalon1g]

Sounds like a badass setup. Post some pics of both your cars I've heard mixed feelings about the 330xi

[Sparky2211]

The 330xi is a great daily driver for this state. I've had the car for about 30,000 miles now with no real complaints. I've done the basic maintenance and a few larger things, but nothing that would stop me from buying another one.

[asshanson]

I'd skip the cam gears. If I remember correctly the HKS cams are designed to be installed straight up, maybe I'm wrong though.

If you can find a buyer for the EMS, I'd recommend ECMLink instead, it's a lot easier to tune and use.

Good luck with your project!

[Shane@DBPerformance]

It's going to run like shit with the FIC 1650s and an AEM EMS.

[Sparky2211]

It's going to run like shit with the FIC 1650s and an AEM EMS.

What do you recommend then?

[scheides]

Maybe the newer high-z FIC 1680's? I have them on my evoX and they are great!

[Sparky2211]

I am waiting to hear back from Shane, but it sounds like 1680's will be the way to go. I am glad that he pointed that out before I ordered them. Is there anything else that I should consider/change thats on my parts to get list?

[goodhart]

I wouldn't bother with the fuel rail unless you need it to fit whatever injectors you plan on running (I know guys that use the Ford 1600's have to use an AEM or similar rail for them to fit).

Use that money for a Fel-Pro Permatorque head gasket :)

[Sparky2211]

I already have a fuel rail. I think I just need the following +/- some.

Parts that I need:
- Gates Timing Belt
- AEM 5-Bar MAP
- AEM Wideband
- BBK 5.0L 75mm Throttle Body
- Mitsu Head Gasket
- Fuel Pressure regulator
- FIC 1680cc Injectors
- Coil-On-Plug Setup

I am open to suggestions though.