Log in

View Full Version : Beater 1g

Pages : [1] 2 3
93gtpeater
05-09-2011, 08:10 PM
I figured I would make a project thread for the talon. I bought it about 2 years ago and have put about 30 miles on it. When I bought the car it came with a 16g but turned out to be a 14b.

Mods when I bought the car

Ghetto fmic
3 inch turbo back
Evo fuel pump
Safc
Wideband

When driving the car home the turbo froze up. So bought a scm61 to replace the blown 14b. when installing the new turbo the oil pan was messed up. so I went to replace the oil pan I pullied the t case off and the output shaft came out with the t case. So replaced the tranny from one I got from trk permance and it didnt make it down my road. The bearings were toast in it. Found a rebuilt tranny put it in and drove it a couple miles on it and the motor started making noise. So I picked up a parts car and put the drivetrain feom that in to my car.

Right now the car runs and drives. But needs a tune and a couple minor things.

Mods now

scm61
850cc injectors
Safc
Wideband
New short route intercooler
Ghetto 3 intake
2g maf
Evo fuel pump
Xtd 4 puck unsprung clutch
Ebay 38mm wastegate

I plan on upgrading to a 255hp fuel pump and get a eprom ecu and have shane tune it.
19TsiAwd90
05-09-2011, 08:41 PM
your gonna need a new clutch soon too trust me... ill show you some pictures of my xtd 6puck unsprung after 500miles other than that looks like a fun project good luck and have fun with it!!
93gtpeater
05-09-2011, 08:57 PM
Iam not worried about the clutch. I have ran lots of xtd clutches and never had a problem. And the way I will drive it tranny will be smoked in no time.
123abc
05-10-2011, 07:26 AM
Iam not worried about the clutch. I have ran lots of xtd clutches and never had a problem. And the way I will drive it tranny will be smoked in no time.


I use a stage 2 XTD Pressure plate and an ACT unsprung 6 puck disc and have been more than happy. 24psi on an e316g, pavement donuts and 2nd gear double clutches don't even phase it.
scheides
05-10-2011, 08:14 AM
Sweet! Where's pics of this beast?
93gtpeater
05-10-2011, 08:52 AM
I will try to get picks up tonight.
93gtpeater
05-10-2011, 07:24 PM
http://i146.photobucket.com/albums/r274/02firebird/dsm/dsm014.jpg

http://i146.photobucket.com/albums/r274/02firebird/dsm/dsm015.jpg

http://i146.photobucket.com/albums/r274/02firebird/dsm/dsm016.jpg

http://i146.photobucket.com/albums/r274/02firebird/dsm/dsm017.jpg

http://i146.photobucket.com/albums/r274/02firebird/dsm/dsm013.jpg
goodhart
05-10-2011, 07:41 PM
bigger pics plz haha
19TsiAwd90
05-10-2011, 07:50 PM
Only issue I had with my XTD was the rivets sheared off from the center hub to the outer hub.. The pressuer plate I'm still using and love it with my clutch net sprung 6 puck
93gtpeater
05-10-2011, 07:52 PM
I couldnt figure out how to make them bigger.