MitsuStyle MitsuStyle

Go Back   MitsuStyle > The Homefront! > Project Talk

Reply
 
Thread Tools Display Modes
Old 06-01-2017   #1561
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

^ Right, as i said far from controlled, just posting the data I have.

There are also other tests out there from other folks with very similar results moving from the eBay core to the Treadstone core.


https://my350z.com/forum/forced-indu...rcooler-a.html
http://www.dsmtuners.com/threads/tre...u-back.465544/
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test

Last edited by Halon; 06-01-2017 at 02:56 PM..
Halon is offline   Reply With Quote
Old 06-21-2017   #1562
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Just some small updates.

- Still moving forward with remote tunes. Vlad said the tune (AFR, Timing, Boost Solenoid type stuff) is looking very solid now. Just some very minor tweaks, but it's pretty solid at this point. So we're starting to look more at some of the "other/extra" features.

- So the two AEM 12pos switches I wired in for Boost and Trac control. We verified I wired them in correctly and AEM is seeing them correctly. So we've activated the boost switch. It starts out at the lowest boost setting (17psi which is roughly WG level). Then increments roughly ~2psi in each position up to I think 29psi is the current highest setting.

- We also verified the front ABS sensor is coming in clean. The rear one isn't for some reason so I need to look into that. I didn't think there was a polarity on these sensors, but I might flip the wires to see if by any chance polarity does matter. Without both working, we can't implement the traction control yet. But with the front one working what we can do is use that for a sort of boost by speed setup. In 1st gear I hook with just a very tiny amount of chirp/spin at the lowest boost setting. So we'll probably just stick with that setting through 1st gear speeds. 2nd gear it hooks decent at the 25psi setting, I have to do some more testing at 28psi, but 2nd gear speeds will probably end up somewhere around 25psi. Then no limit on 3rd gear speeds and above. And really with that in place, it makes the whole traction control piece just a little less important to me since this is sort of already helping me keep traction in check a little bit.

- I pre-ordered up the Grannas 8.8 rear diff kit. I'm going with the 1000hp axle option that retains the stock hubs. I purchased a diff from the local junkyard for $128 that I'll be getting built with a custom gear ratio and LSD. And hoping Grannas can simply make me a diff adapter that will allow me to just keep my current driveshaft. So I'll have my current 3.26 diff with Torsen LSD & Axles up for sale at some point here.

- I remade the cold side IC pipe. It was really cobbled together and was the source of a boost leak. It's been redone and is much better. Fixing these leaks has really made the car feel more responsive, but that could all just be in my head too lol.

That's about it for updates at the moment. I'm getting anxious to setup a dyno appt here soon as well to see where I'm actually at. But here's a screen shot from a 3rd gear log I took yesterday to give some sort of idea of where I'm at right now.

__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test

Last edited by Halon; 06-21-2017 at 02:25 PM..
Halon is offline   Reply With Quote
Old 06-21-2017   #1563
turbotalon1g
 
turbotalon1g's Avatar
 

Join Date: Mar 2005
Location: Blaine, MN
Drives: '91 Automagic
Posts: 13,779
Send a message via AIM to turbotalon1g
Re: Project Lex

Very nice!
__________________
Aaron/brownman/big brown.
'91 Automagic.
Please leave feedback - http://www.dsmtuners.com/forums/itrader.php?u=58309
turbotalon1g is offline   Reply With Quote
Old 06-25-2017   #1564
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Some pics of the car from our Lexus/Toyota/Scion meet we had on Saturday.
Attached Thumbnails
Click image for larger version

Name:	19466732_916411171841540_4244096130478840242_o.jpg
Views:	814
Size:	356.9 KB
ID:	16586   Click image for larger version

Name:	19243011_916415861841071_3721835637006178280_o.jpg
Views:	385
Size:	316.9 KB
ID:	16587   Click image for larger version

Name:	19488493_916537018495622_5687772372822040476_o.jpg
Views:	817
Size:	232.0 KB
ID:	16588  

__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Old 06-25-2017   #1565
Murlo26
 
Murlo26's Avatar
 

Join Date: Dec 2009
Location: Dilworth
Drives: 08 Evo X
Posts: 4,019
Re: Project Lex

Car looks clean, very nice!
__________________
STS/E85/2.2L 10:1 CR

Murlo26 is offline   Reply With Quote
Old 06-27-2017   #1566
turbotalon1g
 
turbotalon1g's Avatar
 

Join Date: Mar 2005
Location: Blaine, MN
Drives: '91 Automagic
Posts: 13,779
Send a message via AIM to turbotalon1g
Re: Project Lex

i want one of these
__________________
Aaron/brownman/big brown.
'91 Automagic.
Please leave feedback - http://www.dsmtuners.com/forums/itrader.php?u=58309
turbotalon1g is offline   Reply With Quote
Old 07-14-2017   #1567
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Had the day off, made a couple quick videos showing where the car is at today. Walk around video and a drive around video. Drive around video was at 23psi. I usually keep it at around that or 21psi for normal driving around, and only turn it up if need be.

Hopefully have some more footage for you next week as I hit the dyno on Monday to see how she does! All I'm hoping for is a number that starts with a 6

https://www.youtube.com/watch?v=HmXJ...ature=youtu.be

https://www.youtube.com/watch?v=-L39...ature=youtu.be
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Old 07-14-2017   #1568
tehehodi
Braaaaaaaap!
 
tehehodi's Avatar
 

Join Date: Dec 2008
Location: Burnsville
Drives: '09 Silveraydo
Posts: 2,016
Send a message via AIM to tehehodi
Re: Project Lex

Did you have it in the waterproof case? I can't hear anything you are saying.
tehehodi is offline   Reply With Quote
Old 07-15-2017   #1569
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Wife lost our normal digital camera that I always use. So I used my Contour 2+ Action Cam. It's got a big piece of solid foam in front of the mic for wind noise, but muffles sound. I also had it turned down a bit. I just did a mod to it tonight so it should be louder and more clear from now on (basically ditched solid foam for a more airy kinda foam).

But I can hear it on my computer, just turn up your volume.
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Old 07-17-2017   #1570
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Dyno'd today. Rented the Dynojet at DBPerformance. Danny was nice enough to run the dyno and the car. Vlad was remotely connected to the Infinity and did all the tuning.

We started off at Wastegate boost (~20psi) and made ~590hp. Over the course of about 2hrs we were all in on this little 61mm (~29-30psi tapering off by redline of 7500). Ignition was starting to break up once we went all in. I brought a spare set of plugs which Danny was nice enough to gap to .020 for me. That took care of the issue and the car was able to make a few clean pulls at max boost.

Ended up at 709HP / 665TQ. Extremely happy with those results as my goal has always been somewhere in the 600's. Here's a couple photos and some videos. Sorry about the sound, they have huge exhaust fans in there which make a lot of backround noise.

Bit thanks to everyone who has helped me with this. I'd try to list all your names but it's impossible to remember everyone. But you all know who you are, thanks a million for all of the help!!! I'm super stoked!





https://www.youtube.com/watch?v=6opb...ature=youtu.be

https://www.youtube.com/watch?v=DzaN...ature=youtu.be
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test

Last edited by Halon; 07-17-2017 at 04:14 PM..
Halon is offline   Reply With Quote
Old 07-17-2017   #1571
A//// Guy
 
A//// Guy's Avatar
 
Bloody Seal Bounce Champion!
Join Date: Oct 2003
Location: South Burbs
Drives: Slowly
Posts: 9,798
Re: Project Lex

So awesome! Nice job!
A//// Guy is offline   Reply With Quote
Old 07-17-2017   #1572
turbotalon1g
 
turbotalon1g's Avatar
 

Join Date: Mar 2005
Location: Blaine, MN
Drives: '91 Automagic
Posts: 13,779
Send a message via AIM to turbotalon1g
Re: Project Lex

Love it, so much TQ!~
__________________
Aaron/brownman/big brown.
'91 Automagic.
Please leave feedback - http://www.dsmtuners.com/forums/itrader.php?u=58309
turbotalon1g is offline   Reply With Quote
Old 07-17-2017   #1573
Alpha D
Got Boost o_O'' m
 
Alpha D's Avatar
 

Join Date: Sep 2009
Location: In a house
Drives: 1991 Eagle Talon TSI AWD Spooling Fiddy Trim Style
Posts: 1,371
Re: Project Lex

Does it still go straight when you get on it ? Scary ...364....bolt it up
Alpha D is offline   Reply With Quote
Old 07-17-2017   #1574
93gtpeater
 

Join Date: Apr 2008
Location: stillwater
Drives: cbr 1000rr repsol
Posts: 1,421
Re: Project Lex

Very awesome. So 700 on kill mode? Pretty sweet you made all that power on stock motor. Congrats. Wish I had the balls to push the limits of my car.
93gtpeater is offline   Reply With Quote
Old 07-17-2017   #1575
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

Yeah 700 with my boost switch turned all the way up. But I like to cruise around town with it down at like 21psi because no need to push it hard unless I have to, like if Peter rolls up in his Vette next to me lol. Seeing how the car did today, even 21psi should be right around 600hp so plenty of fun to be had there and plenty to gap 99% of what's out there usually anyway.

Yeah the car goes straight. So today we also added in Boost by Gear. So in 1st gear now the car will be on WG boost no matter what, then every gear after that it'll just be whatever I set it to on the switch. I'd really like to try and make a pass this year as I'm pretty sure it has 10's in it now even with my shitty driving, and the Boost by Gear I think will help me getting out of the hole in 1st gear which is what I struggled with in the past on this car.
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Old 07-17-2017   #1576
93gtpeater
 

Join Date: Apr 2008
Location: stillwater
Drives: cbr 1000rr repsol
Posts: 1,421
Re: Project Lex

It should run 10s pretty easy with that power and boost by gear. Plus those big meats in the back...... proving grounds in the fall?
93gtpeater is offline   Reply With Quote
Old 07-17-2017   #1577
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

That's the plan. It's all gunna come down to if I can figure out how to launch it. Best 60' I've done yet was a terrible 2.1 or something I think lol. All I need is maybe a 1.9 and I should be in the 10's I think.
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Old 07-18-2017   #1578
C3L1CA
N17r0U$ br4D
 
C3L1CA's Avatar
 
Goosehead Racing Champion! Street Drifting Champion!
Tournaments Won: 1

Join Date: Apr 2007
Location: Oakdale, MN
Drives: bikes and a silveraydo
Posts: 2,727
Re: Project Lex

Awesome numbers! I gotta ask as I'm a bit slow, why is the graph so choppy up top?

Be fun to see that thing make some passes, hopefully I can make it to proving grounds and see it in action!
__________________
My rice rocket best times
Pump Gas: 8.85 @ 152.3 in 2016
Race Gas: 8.982 @ 152.16 in 2014
C3L1CA is offline   Reply With Quote
Old 07-18-2017   #1579
A//// Guy
 
A//// Guy's Avatar
 
Bloody Seal Bounce Champion!
Join Date: Oct 2003
Location: South Burbs
Drives: Slowly
Posts: 9,798
Re: Project Lex

Im guessing because no correction and no smoothing? This was on E85 right? So solid! Now you need to find a different car to put that built motor/turbo into and just rock this one as is.
A//// Guy is offline   Reply With Quote
Old 07-18-2017   #1580
Halon
Pewp Champion
 
Halon's Avatar
 

Join Date: Nov 2003
Location: Blaine
Drives: Teh Bean
Posts: 12,026
Send a message via AIM to Halon
Re: Project Lex

It's choppy because smoothing is set to 0. So my understanding is it's basically the raw signal. For whatever reason that is what Vlad prefers. I could add smoothing to make it smoother, which I believe is what most people do. Doesn't really make a difference to me though.
__________________
B-Man - FlexFuel Mafia
1991 TSi AWD E85 - BEP S362, DSMLink V2, Built 2.0L Idle Vid 628hp Graph 541hp Vid 10.93@137 Vid
1992 SC300 E85 - BW 84-75, Vlad Infinity, NA-T, 6spd Idle Vid 709hp Graph 709hp Vid 11.1@131 Vid
2006 Bayliner 195 - Carbed 5.0 Top Speed Test
Halon is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 03:14 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.