Built 92 Laser AWD Laser AWD parts car

[slowbubblecar]

***Price drop to $1,000 if gone by the end of the week***

Price: Asking $1,200/BO and it is
Location:Minnetonka, MN
Condition: Fair

Purchased the vehicle from a member a few years ago with the intent of pulling the parts out to put in another vehicle and junking the body, but I didn't have time to mess with it and it is just sitting at one of my houses now.

Below is a list of the mods:

MAP Performance stage 1 2.0 shortblock - 6 Bolt (less than 1,000 miles, but sat the last several years)
-Hot tank/boil block
-Polished crank
-Balanced
-ACL Race series main and rod bearings
-Overbore with torque plate
-Fully decked
-Mahle 8.5:1 Forged pistons
-Eagle rods
-Balance shafts eliminated
-New front case: Oil pump, oil pump drive gear, oil pump driven gear
Head:
-Used good condition cylinder head that was rebuilt as well
-Brian crower valve springs and retainers
-new exhause and intake oil seals
-5 angle valve job

-16 Gallon Fuel cell
-280 fuel pump
-255 inline fuel pump
-Adjustable Fuel pressure regulator
-Small 16g
-Pacesetter tubular manifold
-Fidanza 3.2 Clutch and pressure plate/throwout bearing
-boost and A/F gauges on A pillar
-Adjustable throttle cable
-gates racing timing belt

The vehicle does not have FMIC, exhaust, BOV, intake and likely other parts. It is as it was when I purchased it.

Below is a link so you can see a few additional pictures and a project thread from a prior owner. I purchased it from the person who bought it from this guy. The bumper is off of it, the hood is black and several interior items are missing.

http://www.mitsustyle.com/forums/sho...ighlight=laser

Selling the car as a part car with no title. It is possible to get it titled, but it would take a little time/work to complete the process and I didn't think it would be worth the hassle.

James

[turboimports]

Do you know what camshafts are in it?
Have you tried to spin the engine manually?

[slowbubblecar]

No idea what type of cams are in it. I don't know anything more than what the link in the referenced post says. I purchased it to use the motor and a few other parts with plans on dumping the body, but I never touched it since buying it due to a lack of time and work travel. The only thing I did was tow it. I'm not sure if MAP has any records on the motor but I doubt anything has been changed since they worked on the motor. I did notice it has some adjustable cam gears though.

I'm working in New York now but may be able to try to spin it over this weekend.

[s1ngletracker]

If someone buys this and parts/scraps the shell, can I get a few pieces off it?

[Alpha D]

so its not a part out but by as whole instead hmmm

[slowbubblecar]

I don't have time to part it out. Someone could make a few bucks if they wanted to buy it and do it though.

[goodhart]

I want the harness

[sleepydsm]

HORT

[slowbubblecar]

Lol-the good old times of that, QPR, university and embarrassing old men driving around town.

[dsmDolney]

This is so tempting its not even funny. How much is several years ?

[slowbubblecar]

I'd have to guess that the car hasn't run since close to 2010-2011 (timeframe in the link I posted). I don't know for sure though. All I know is that the guy I got it from didn't do too much with it.

[goodhart]

Tyler, buy it and part it

[dsmDolney]

I dont know yet mike. It was a thought but i dont really have the space or time.

[slowbubblecar]

SOLD