![]() |
Winter plans/mods 2011
What's everyone up to car wise and i guess otherwise since this isn't much of a car/tech forum anymore.
I moved and we are cleaning the garage up to get my car inside and then I'll be installing a few parts that I've had laying around for a long time. (ES bushing kit, '06) Apart from that I'll just be cleaning up the car and fixing small leaks and things I don't like. Apart from that score a fulltime job and maybe move again depending on where I get employed. |
Re: Winter plans/mods 2011
Car wise, I'll probably need new tires later this winter and at that time I might do a Whiteline Roll Center Kit. Other than that just gas and maintenance!
|
Re: Winter plans/mods 2011
Well, I moved mine out of it's nice spot in the garage to outdoor storage, hopefully I'll be more motivated next spring. Just don't really care about it right now.
|
Re: Winter plans/mods 2011
going to get the spyder done and ready to go by spring.
start working on the evo some more. get the rear end back in it. also have to have the 2.4 block machined, get a head done and get a set of cams for it |
Re: Winter plans/mods 2011
Probably do another oil change in 5k miles, since I just did one. That should put me safely at spring time.
|
Re: Winter plans/mods 2011
Quote:
|
Re: Winter plans/mods 2011
Swapping in a full 3" exhaust with quiet/loud switchable mufflers, and maybe a wideband.
Oh and maybe this if I get motivated: http://www.turbotechnologyinc.com/c6/c6kit.jpg |
Re: Winter plans/mods 2011
I'll need to pull the engine to drill out the 2 center bearing bracket bolts on the drive shaft I sheered off. Then I should probably rebuild my prop shaft as it's making quite a racket since installing solid bushings. I also need to replace the seals on my power steering rack... they finally gave up the ghost after 21 years.
For fun stuff, I've got fully poly bushings for the rear end, including the moustache brace. I also am planning on lighter 17x9 wheels with 255 wide rubber on all 4 corners. |
Re: Winter plans/mods 2011
I'm at a point where it's just finishing touches. Once everything current works correctly, GrimmSpeed 3-port BCS and Omni 4-bar MAP sensor, speed density tune with a high and low boost maps so I can just leave it alone, and then just driving and enjoying it.
Hopefully by spring get the blown MR Bilsteins I picked up rebuilt and revalved for Swift Spec-Rs, and probably just solid sway bar links in the rear to give it a little more stiffness and less roll/play. T-case rebuild in there somewhere too before Proving Grounds. |
Re: Winter plans/mods 2011
I'm hoping to do a 3" TBE and get everything ready for an e85 switch and 3port for a tune by spring.
|
Re: Winter plans/mods 2011
I plan on going 35r and having my center welded this winter. proably upgrade injectors since those are maxed out. Would like to change my cams out for some 280s. If its together in the spring I can get my cage weleded in
|
Re: Winter plans/mods 2011
Start the swap to automatic soon. Attempt to save up enough scratch for a nice roll cage. Re-upholster the front seats so they look nice again! And make a choice on wheels. If I could get all of that done before proving grounds (yeah right!) I would be extremely happy.
|
Re: Winter plans/mods 2011
^u better make a pass this year!
|
Re: Winter plans/mods 2011
Stroker kit, bigger cams, valvetrain, IM and TB.
Oh, and I'm trying to get it done by Tx2k12. |
Re: Winter plans/mods 2011
^Take me with you!!
|
Re: Winter plans/mods 2011
Megasquirt and bigger injectors to run e85 on the mr2. DSM gets more expensive parts.
|
Re: Winter plans/mods 2011
I am not sure on my mods yet on my new car! but I know I want to do the aux port mod, and update the nav and unlock the nav, fresh paint on the grill, paint the subaru badge, save for stage 2 parts/tune, and just enjoy it!
|
Re: Winter plans/mods 2011
^^Whats ur new car?
|
Re: Winter plans/mods 2011
Nothing.
|
Re: Winter plans/mods 2011
Why do I look at this shit?
|
All times are GMT -5. The time now is 12:23 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.