Re: Project Lex
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
|
Re: Project Lex
Yesterday I was able to work on the car for about an hour. All I did was pull the carpet back and add some additional electrical tape to the wires I tapped into to ensure no conductors were exposed. The sync problem still remains however :( My next plan is going to be double checking some settings in TS. If that doesn't fix it, then I am going to double check the ground wire, and maybe see if I can't improve that. Then I will rehook up the stock ignition wire, and see if the sync issue goes away. Then just keep working my way back trying to figure it out...
|
Re: Project Lex
8 Attachment(s)
Well today got a little bit done. The original vacuum source I was using wasn't very good (kPa value would freeze soon as the TB closed). So I found a different spot and tapped it from there.
http://mitsustyle.com/forums/attachm...1&d=1296608917 Also decided to work on the sync issue as well. I was told to double check the base ignition timing on the car. So I looked up how to do it and went to it. Should be set to 10*. I found mine was sitting at about 12*. Clocked the dizzy and set it up right on 10. Here's a little how to if anyone ever needs to know how to set base timing on a 2JZGE. ------------------------------------------------------------------------- SETTING BASE TIMING ON A 2JZGE (1992 SC300) - Find the diagnostic port in the engine bay, and jumper terminals TE1 and E1 with a paperclip. http://mitsustyle.com/forums/attachm...1&d=1296608917 http://mitsustyle.com/forums/attachm...1&d=1296608917 - Connect the timing light to the battery, and to plug wire #1 http://mitsustyle.com/forums/attachm...1&d=1296608917 http://mitsustyle.com/forums/attachm...1&d=1296608917 [img][/img] - The timing marks on the plastic cover will read | 10 | 0 (this is in increments of 5 so it read it as 15 10 5 0 ). With the pins jumpered, you want it set at 10. http://mitsustyle.com/forums/attachm...1&d=1296608917 http://mitsustyle.com/forums/attachm...1&d=1296608917 - Point the timing light and look for the line on the crank. It should line up at 10. If it does not, there is a single 12mm nut you need to loosen on the distributor. Clock the dizzy until the mark lines up. http://mitsustyle.com/forums/attachm...1&d=1296608917 - When you're done, tighten the nut back up on the distributor, and check the timing one last time to ensure it didn't budge while tightening the distributor. Remove the jumper. With the jumper removed, you will notice the timing will advance a bit automatically which is normal. |
Re: Project Lex
Well it's been forever since I've updated this. Mainly because there has been nothing to update as life has been quite hectic since the beginning of the year.
Today I finally got some time to continue troubleshooting the sync problem. Put a scope to the Cam and Crank inputs as noise was suspected as being a possible cause of my sync/tach issue. Here's a nice vid. Looks clean to me. It's a 24 tooth (no missing tooth) crank signal, and I have just a single G2 cam signal coming in. You can see pretty clearly that they look pretty clean. You see the single Cam trigger, then 24 Crank signals. I'm no expert but it doesn't look like there's much noise on there at all. What I do notice is how close the cam trigger is to the crank trigger. From what I understand, you do not want those to line up perfectly. The cam trigger should come in between two of the crank triggers. Maybe that is my issue? If anyone has any advice, feel free to share! And big thanks to Shane at DB Performance for lending me the scope. Greatly appreciated!! http://www.youtube.com/watch?v=gs2vCC5x3KY&hd=1 http://www.youtube.com/watch?v=gs2vCC5x3KY |
Re: Project Lex
OK did a little bit of playing today per the advice of some gurus. I played with the Zero Crossing pot, and with the different edge triggering options. See pics below.
BEFORE Adjusting Zero Crossing pot log. http://www.msextra.com/forums/downlo...e.php?id=17743 AFTER Adjusting Zero Crossing pot log. http://www.msextra.com/forums/downlo...e.php?id=17744 - Zoom to see where the cam trigger falls in comparison to the crank triggers. Ideally it should fall exactly between two of the crank pulses. I played with the different edge options. This pic shows the best combination I could get which is Falling Falling. http://www.msextra.com/forums/downlo...e.php?id=17745 So the cam signal is much better now. But I'm still having the same problem. The cam pulse appears to be as steady as can be, so the crank signal has to be the cause of all this. Will continue this battle this weekend and hopefully get this thing working!! |
Re: Project Lex
Wow, seeing you deal with all that makes me feel a little better about the crap I had to go through to get my truck running.
|
Re: Project Lex
Ha, there definately is a learning curve, but everyday I'm figuring it out a little more. Hopefully have this worked out this weekend.
|
Re: Project Lex
Had a couple minutes to look at some more stuff. In this video I'm reading the raw cam signal (G2) coming in, and am reading the processed cam signal on JP2 pin 18 on the silver MS3 board. In a nutshell MS just takes the sine wave signal, and creates a square wave based on where the raw signal crosses the 0V line. Thanks again Shane for the scope, I wouldn't be able to do any of this if I didn't have it.
http://www.youtube.com/watch?v=t3eBiVhBgWo&hd=1 |
Re: Project Lex
All this signal checking crap has finally convinced me to buy my own scope. Big thanks again to Shane for lending me his as it's proving to be a huge help, and helping me learn a ton about how MS works. I'm hoping he'll let me hang onto it for a little bit longer yet until I get the hang of my new scope.
http://www.hobbylab.us/default.aspx That's what I got. $129 It's a USB based device that you use with your computer (I'll just use it with my little netbook). It's been used by a few of the MS guys and they've all said it works quite well. It's a 2ch Oscope, and a 16ch Logic Analyzer. The software is apparently pretty easy to navigate as well. I heard the probes that come with it leave a little to be desired, so I picked up some better ones off Ebay for $12 shipped. Someday eventually I'd like to get a true standalone scope w/ 4 channels, but for now this seemed like a great starter unit for a decent price. But in the future, if I could find some old analog Tektronix 4ch sucker for cheap on Craigslist, that'd be cool :) |
Re: Project Lex
Checked signal at J1 which is the crank square wave. Here's a vid of the crank signal. Was hoping I'd find a smoking gun on this today and be able to work it out with the filtering function in TS, but nothing really caught my eye.
http://www.youtube.com/watch?v=SD4od1097tA&hd=1 After looking at the square waves of both the Crank and Cam, it seems like the correct settings for this in TS would be Rising & Rising. Starting to run out of ideas here as so far nothing has stood out to me as being an issue thus far. I'm going to take another video comparing the square cam & crank to show how they match up. After that, I really am starting to run out of ideas. I just ordered up a HobbyLab USB scope so I should be able to take some logs with it with the Logic Analyzer function that might be able to tell us more than this old scope meter. |
Re: Project Lex
Is it an ignition or fuel problem, or a problem at the root of both systems? If it could be one or the other but not both, have you thought about working backwards straight from the ignition or injectors?
|
Re: Project Lex
I have unhooked the ignition, so the ignition is being run by the stock ECU again, and MS is only controlling the fuel. MS is losing sync, which is all driven off the Cam and Crank position sensors. MS needs to see 24 crank pulses, then 1 cam pulse, then 24, then 1, and that's how it stays 'synced' with the motor. When it loses sync, it shuts off the outputs to be safe (so in this case, fuel) which is why you hear the hesitation. The sync error code I receive is 17 which means something like "wrong amount of crank triggers before seeing the cam trigger". Whether or not it's something in the hardware that is the issue, or a setting in the software, I am really unsure of. Support from the guru's are starting to fade little by little as well which doesn't help.
And here is a vid of the crank vs. cam square waves. http://www.youtube.com/watch?v=kfUace3pZzM |
Re: Project Lex
OK well just took a wild stab and it seems to be 100 times better, although not completely taken care of. Since earlier some signs were telling me that the crank trigger was the likely cause of this, I decided to enable crank only filtering. I used the Tach Rejection feature, and set it to 30% as that was a value I had seen thrown around in the filtering documentation on here. And what do ya know, the issue seems to have 99% gone away. You'll see in this video that it still lost sync a couple times under WOT, but way better than before. I will play with filtering a little bit more and hopefully be done with this issue.
One thing I did notice was that in the composite log, the crank now shows up as a square wave instead of just a single edge as it did before. No idea what that means however. http://www.youtube.com/watch?v=EZPwl3fj34I |
Re: Project Lex
Played with the filtering a bit. I have the global filter time now set to 5uS. That basically means, any pulse that is less than 5uS in length gets filtered out. Anything longer than that is considered good and is used. So basically goes off the assumption that good signals are long, and noise is short.
I then set the rejection percentage to 70%. That means that it predicts when it should see the next pulse. So anything that happens within the first 70% of that time gets ignored. For example say it predicts it'll see the next pulse in 100ms, it'll wait for 70ms until it even starts looking for it again. So any noise that is occurring in the first 70ms is completely ignored. Car is running like a champ!!! Goint to hookup the ignition again and make sure she's running good still. If so, I may start talking to Shane about getting a quick base tune before the turboing begins!! |
Re: Project Lex
^Awesome.
|
Re: Project Lex
Bman, the new MS guru.
|
Re: Project Lex
NICE!! Turbo'd by dyno day?
|
Re: Project Lex
Glad to hear you sorted it out...was getting worried there for a while. Looked like a tough little cookie of a problem haha.
|
Re: Project Lex
Glad you figured it out, cause that shit was way over my head haha!
|
Re: Project Lex
I understood a lot of it, and I'm glad it was you doing it, not me. ;)
Good work sir. |
All times are GMT -5. The time now is 10:55 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.