my new project
Well as some of you know I bought swiftys talon and since most of you already kinda know the car I wont go into too much detail about it other than what is currently going on with it and what I'm doing to it.
I bought the car figuring It I would be pretty set. It just needed to be tuned for new injectors and I'd have an awesome car to putz around in this summer. Well with the way my luck goes I'm about 90 percent sure something went wrong with the #3 injector (i'm going to have them bench tested to verify) and the cylinder pretty much ate it's self. they were brand new injectors too. I removed the cylinder head to inspect the damage. the cylinder head and piston were quite melted in cylinder 3 and one of the intake valves broke or melted off and did a number on the cylinder wall in cyl3. Ok where I'm sitting now for the cylinder head. I have a good core to have my parts swapped into and it will need new valves for cyl 3 and it will have to be machined for the over sized valves. I'm debating whether or not to have it ported and polished too. As for the block I'm not sure if I can get away with just honing it out so I'm going to pull the block and bring it someplace (not sure where yet) to have it checked out and see what the best route to go with it is. Idk if you can have a 4g63 sleeved or if it's just better to bore it out and go with over sized pistons. I would like to reuse as many of the parts as I can since all the rods look good and 3 of the pistons should be reusable. In regarding the block if anybody who has some experience with engine building as any advice please feel free to chime in. It will be greatly appreciated and then there is the turbo. a bunch of metal went through the exhaust and dinged up the turbine wheel pretty bad so it will at least need a new exhaust wheel and a rebuild. depending on what ends up happening with the block I might look into upgrading to a billet version of the gt4294 or look into a gt4202/gtx4202 Sorry this is such a long post but that is kind of the short version lol |
Re: my new project
5 Attachment(s)
Here are some pictures of the carnage
|
Re: my new project
Congrats on the new purchase! Perhaps maybe it will see the track now. Lol
As far as a place to bring it to get looked over. Motors by gosh is a good place. There located right next to DB. Are those the FIC 2150s? I've heard they were having issues but I can't remember what the issues were. Good luck with the car |
Re: my new project
Quote:
|
Re: my new project
All I could fibd for failures doing a quick goggle search was that of storage. If they were not stored properly and cleaned water could get in causing irreversible failure.
|
Re: my new project
Could have dropped a valve or broke a valve and have all that happen too.
|
Re: my new project
Quote:
Quote:
|
Re: my new project
Here's a little update of where things are sitting right now. I finally was able to get the injectors bench tested and they tested good. The flow and pattern are basically identical on all of them. So it's looking like its just a broken valve that's the culprit.
The shortblock is up at MAP right now being built. Had to get a new block, front cover, then we're putting different pistons in it (wiseco hd's), we're reusing my crank and rods, and putting a main girdle in it too. It will still probably be a few weeks until I get it back then the head will be going to the head shop. |
Re: my new project
Ouch. Sucks it caused so much carnage. :(
|
Re: my new project
Quote:
|
Re: my new project
Quote:
|
Re: my new project
A little update on the car. I got my shortblock on Monday. It's a MAP stage 2 with a kiggley main girdle. So i can concentrate on the head now. I'm not 100 percent sure what route I want to go with the head yet. I'm going to order a rebuild kit for the twin disk then the shortblock will be going back into the car. It will be nice to finally be able to do some work on it.
|
Re: my new project
Looks like the carnage I experienced when I had a valve fail too. I was gently cruising at 50mph when it happened to me. Never did figure out the reason why but valve failure was the only yhing that made any sense. The stock valves are a 2 piece design, so I guess it could be possible.
Good luck getting her back up and running. |
Re: my new project
Quote:
|
Re: my new project
I dropped the cylinder Head off at the head shop this morning and they said they think a valve seat dropped and that's what caused the valve to break. They also said that every valve hit a piston and is bent. Not sure what happened there either.
|
Re: my new project
^mistimed? .
|
Re: my new project
Yeah idk everything swiftys told me about the engine that was in it seems to have checked out for the most part. He said he got the valves from Brent Rau so either the valves were bent when he got them, it was mistimed, or the cams were degreed wrong or the cam gears slipped. Idk lol. Pm me and elaborate on what you've heard if you don't mind.
|
Re: my new project
PM sent.
|
Re: my new project
Dang Shawn. Good luck on the rebuild, it'll be awesome to see that thing driving around!
|
Re: my new project
Quote:
|
All times are GMT -5. The time now is 08:22 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.