4seasons69, poor
well recently i asked for help screwing in the clutch adjustment rod and getting the clutch all adjusted for 25 bucks, as stated in this thread. i ended up just giving him 30 bucks off what he owed me for a motor i sold to him earlier.
http://www.mitsustyle.com/forums/showthread.php?t=24818 4seasons69 cam out to help me, poked around under the dash for a half hour or so before finding out the threads were bad. after that he said he would be back the next day with a tap and die kit. the next day i get a call saying he had to work late and come in early so it would be a day or 2. after that i didnt hear from him for 2-3 weeks, so i finally went out and bought a whole new master cylinder cause i dont know if you can take the rod out, or where to buy just a single rod. and i needed this done ASAP due to threats of having it towed. after i got it home i talked to him asking for my 30 bucks back, as he didnt do what i paid him to do. i was basically told to f-off and that i was lucky i didnt get charged what he normally charges for side work. so for the most part i ended up paying 30 bucks for him to come to my house, poke my car for a few minutes and accomplish nothing |
Re: 4seasons69, poor
Quote:
4seasons69 - Please work out a deal with the OP to make this situation right. |
Re: 4seasons69, poor
love this new wave of noobs.
I've sold stuff to the guy before. good luck |
Re: 4seasons69, poor
That's sketchy to not have stopped by over again after getting $30 so personally I don't care if he's a 'no0b', its kinda bs to take money and not do the favor that was suppose to be done.
|
Re: 4seasons69, poor
I told you to just DIY :P
This is a pita thing to do, not sure how the threads would get all stripped though. You obviously got under there yourself to do it, since you got the new master cylinder installed right? Make him buy you some beer, drink a few together, and get over it :D |
Re: 4seasons69, poor
well at the time i didnt want to replace the master cylinder, i just needed to get the rod in so i could drive it 4 blocks. but i was also thinking it was going to be a good bit harder than it was as well
|
Re: 4seasons69, poor
ok so I was out there for at least 45min messing around with his car. (I've done this many times on my car and usaually only takes a couple minutes) to find out that he messed up the threads on the master rod. so I tell him I can probably try to come back with a tap and die set and see if we can get the threads cleaned up good enough to screw it in if that doesn't work your gona need to replace it.
long story short one of the guys at my work just had a baby a few weeks ago and was out and then last saturday the day techs wife died. so i've been working extremely long hours and haven't had time to do anything but work. I sent him a couple texts filling him in on what was going on but never heard back from him. I did what I could with his car but I said i'd do the clutch rod and adjustment cause they are quick. I never told him I would put in a master cylinder for 30 bucks you wouldn't bring your car into a shop to have it diagnosed and expect them to do it for free unless your crazy that's not how it works. i'm a mechanic and time is money and my time isn't free. but since he's so butt hurt over 30 bucks i'll give him his money back |
Re: 4seasons69, poor
oh and I had offerd to let him borrow my tap and die set since it had been a while and still wasn't able to make it back out there with no reply as well.
and there was NO money exchanged he never gave me 30 bucks. I owed him some money for an engine I bought from him and knocked 30 bucks off of what I owed him. I was told it was a 6 bolt with an evo3 head with port work. after some research and more inspection it was definitely a 1g head with no signs of port work so who knows if it actually had as low of miles as he was claiming. I let it go and didn't run a muck because it was a used part and people lie all the time when they sell used stuff. |
Re: 4seasons69, poor
i said in my original post that i gave you 30 off what you owed me for the motor.
i also gave you the exact information i got from MAP, whom bought the motor (used) and inspected it for me. so dont try and play it off like i blatantly lied to you. http://www.mitsustyle.com/forums/showthread.php?t=20284 is what MAP got for me i went and borrowed a tap and die kit on my own, since i wasnt able to use it under the dash and had to pull the whole cylinder out. i just decided to replace the whole thing and get a new rod all together in the process. bottom line is, i docked 30 off what you owed me, and didnt get anything out of it. in addition to that, the whole reason i was offering money in the first place was because there was a threat of it getting towed, so doing it quickly was the goal. its not exactly fun telling people that your car will be off their property, then getting put off by the person who is supposed to be helping you for money. |
Re: 4seasons69, poor
Quote:
|
Re: 4seasons69, poor
Quote:
Sorry to hear about the problems Randy, hopefully he makes it right. If I wasn't in Spain I woulda helped ya. |
Re: 4seasons69, poor
OK, just tack the 30 dollars back on if you are unsatisfied. Isn't that the simpler solution? Im not saying thats fair for 4seasons. But eh you uys figure it out!
|
Re: 4seasons69, poor
Why didnt Viridion just take the master cyl out and rethread instead of buying a whole new master.
They are actually really easy to take out, (ive done about 15 of them), and if the threads were totally fucked, you can easily replace the rod only. |
Re: 4seasons69, poor
Quote:
|
Re: 4seasons69, poor
Quote:
i tried pulling it out, it wouldnt budge for me, and since it was out, it was just easier to replace the whole cylinder. also the new master came with the pivot arm, that needs to be replaced when i weld the pedal assembly, because right now i have a nut welded onto the end of mine |
Re: 4seasons69, poor
Why dont you split it, $15. He did after all come TO YOU in your time of need and tried to help you. I think his gas and time is worth more then nothing. Just my $.02
|
Re: 4seasons69, poor
Quote:
There is a C clip that you have to take out in order to get the rod out. A bunch of the masters that i have replaced come with the wrong rod so you need to reuse the old rod, depending on which one you get. (the N/T ones are a different rod.) |
Re: 4seasons69, poor
Quote:
the new master came with a new pivot arm and rod so i dont have to worry about having the wrong pieces |
Re: 4seasons69, poor
well from what i've heard this isn't the first time he's done something like this and likes to try and get as much as he can out of a person.
Quote:
|
Re: 4seasons69, poor
While I like to be fair as I can, I can honestly say I am disappointed in this wave of people that don't seem to want to do shit themselves.
Sadly my friend as I learned the hard way is that not all DSMers are nice guys. |
All times are GMT -5. The time now is 04:50 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.