Re: GsXtUrBo98's 2G project thread
 

I hear the time thing. Pm me your address if I'm in the area I'll toss it in your mailbox. Lol

Re: GsXtUrBo98's 2G project thread
 

Lol that works

Re: GsXtUrBo98's 2G project thread
 

"He also recommended running speed density with a AEM 5 bar. My GM MAF is all over the place."

I believe im having the same problem with my gm maf... Your tunimg with dsmlink right? Was your mafraw readings just rediculously high? And have you looked into going speed density? Cost wise?

Re: GsXtUrBo98's 2G project thread
 

Shane was telling me that GM mafs on higher HP cars is hard to tune.. And yes it was a little crazy. Cost wise I haven't dug too much into it yet. That can be for next year or at least after proving grounds.

Re: GsXtUrBo98's 2G project thread
 

Oh ya i'm on link v3

Re: GsXtUrBo98's 2G project thread
 

nice. 10s at pg?

Re: GsXtUrBo98's 2G project thread
 

I think I'll need a driver mod... I have a problem with my 1,2 shifting..

Re: GsXtUrBo98's 2G project thread
 

So do you know what does it take for me to go to speed density aem 5 bar map sensor? Im running v2 dsmlink and my maf readings are just rediculous!

Re: GsXtUrBo98's 2G project thread
 

V3 upgrade, plus the 5 bar and IAT sensor wired into the ECU should be it.

Re: GsXtUrBo98's 2G project thread
 

X2.

Re: GsXtUrBo98's 2G project thread
 

^ this

Re: GsXtUrBo98's 2G project thread
 

Make some more track days!!

Re: GsXtUrBo98's 2G project thread
 

Too busy with work...

Re: GsXtUrBo98's 2G project thread
 

I know exactly how you feel, I'll let you know if I ever make it. Going in a group is nice. :nod:

Re: GsXtUrBo98's 2G project thread
 

Definitely!

Re: GsXtUrBo98's 2G project thread
 

Dude, I'll need to come drool on this thing some day before/after work, where in Lino are you?

Re: GsXtUrBo98's 2G project thread
 

Just off of country road j and Hodgson/rice street.

Re: GsXtUrBo98's 2G project thread
 

Oh ok, prolly like 10 min from the prison then is all

Re: GsXtUrBo98's 2G project thread
 

Ya about that.

Re: GsXtUrBo98's 2G project thread
 

Ha right around that ridiculous house with all the Xmas blow up stuff!!!!

Re: GsXtUrBo98's 2G project thread
 

Yes just down the road from there.

Re: GsXtUrBo98's 2G project thread
 

Got the axle in and changed the oil. Also, I ordered my cdi ignition box from map and should be in on Monday

Re: GsXtUrBo98's 2G project thread
 

Went and picked up my dyna tec cdi today from map but did not install.. Went to the gas station to fill her up and she runs great with the fresh gas but the rear end still clunks even after replacing the 2 rear axles with hd ones..... I guess it could be the rear diff itself..

Re: GsXtUrBo98's 2G project thread
 

Does it clunk when shifting? If so, it's probably the rear diff bushings. Evo's do the same crap. Doing new rear diff bushings and driveshaft bushings cures it most the time.

Re: GsXtUrBo98's 2G project thread
 

No, its only when I'm making a sharper turn.

Re: GsXtUrBo98's 2G project thread
 

Does it clunk driving strait, turning, or both?

Re: GsXtUrBo98's 2G project thread
 

Turning

Re: GsXtUrBo98's 2G project thread
 

Do you have a welded center diff?

Re: GsXtUrBo98's 2G project thread
 

He does

Re: GsXtUrBo98's 2G project thread
 

Are you sure that isn't the noise you are hearing?

Re: GsXtUrBo98's 2G project thread
 

That is def from having a welded center diff. Happens to all with a welded diff if you are turning in tighter areas.

Re: GsXtUrBo98's 2G project thread
 

So I installed a dynatek arc2 and am still having break up problems.. I was at 27psi and turned it down to 25psi and it wasn't as bad. But then I turned it down to 22psi and she goes pretty damn smooth through the gears.. I think I'm in need of a retune..

Note: I also fixed some boost leaks but there isn't any difference from before or after since they were before the maf

Re: GsXtUrBo98's 2G project thread
 

What are your plugs gapped at?

Re: GsXtUrBo98's 2G project thread
 

20

Re: GsXtUrBo98's 2G project thread
 

what plugs?

Re: GsXtUrBo98's 2G project thread
 

Ngk bpr8es

Re: GsXtUrBo98's 2G project thread
 

If they're more than a couple months old, I'd try new plugs first.

Re: GsXtUrBo98's 2G project thread
 

Why are you running those plugs may i ask?

Switch to BR7ES and see if that changes. If you are on E85 those may be too cold.

Re: GsXtUrBo98's 2G project thread
 

The plugs are brand new just installed. Brad ran them in his 2g so I through them in last year and hadno problems..

Re: GsXtUrBo98's 2G project thread
 

hmm, i guess I'd try the BR7ES and see if they help any, cheap enough to try.