Re: My Talon
 

how much it cost?

Re: My Talon
 

The complete brand-new CHRA should be about 500.

The turbine shaft/wheel is $200 alone... plus labor, plus rebuild kit, plus new center section= more than $500 so the entire new CHRA is the best bet.

Re: My Talon
 

Well my center section didn't fail... I thought the shaft seized, because I could not move it with my hand, and the oil fitting was loose and oil was on the fitting. But the center shaft is not blued at all, and the bearings are perfect. There is a clean break on one of the fins of the turbine shaft, and the people at DC said it most likely broke off and the foreign object and out of balance wheel is what cause the destruction. The shaft is actually bent, too. So if the shaft did bend, and wear into the cast center section I would have just needed a new turbine shaft.

Re: My Talon
 

Thanks to Dennis at Diesel Components. I have a brand new shiny Holset CHRA. It set me back about $550 :( But hey, my car will be going by tomorrow.

Next on the agenda:
Install turbo
Run at the track
All new front end parts and alignment
Maybe a Rasky's detail session????
Take nice pics while shes clean and shiny.

Re: My Talon
 

Good to hear!

Re: My Talon
 

Hell yeah, great news!

Re: My Talon
 

Kevin's (sleepydsm) first run at rock falls
http://i118.photobucket.com/albums/o...h_MOV00811.jpg

Re: My Talon
 

That is awsome... Congrats kevin!

Re: My Talon
 

Heck yeah. I was excited when you ran that. Great time man!

Re: My Talon
 

127mph is pretty good. What's the race weight again?

Re: My Talon
 

I had a 1/4 tank of e85. I'm about 190lbs., so maybe 3200w/driver?

Seems like my car has no low end and mid range power, it really doesn't launch hard. I think the 2G timing map on the car is too conservative.

Reguardless, I am really happy with what it ran, a lot quicker than I thought.

Re: My Talon
 

Yeah that is damn impressive for the power you're putting down! Who knew you could actually drive.. ;)

Re: My Talon
 

Hmm, this car may be for sale now lol. I need to take a few nicer pics.

Re: My Talon
 

Why..?

Re: My Talon
 

I've done pretty much everything I've ever wanted with a dsm with this car (make over 400awhp on DD, run a decent 1/4 mile, and beat a very intimidating V8 car in a race where I was completely underestimated), and I've owned 1G awd's my entire life. I'm kinda ready for something new. I really like projects, and I actually complete them!

But we will see, because I have really put a ton of time and effort into this car, it really isn't worth selling!

Re: My Talon
 

I'm getting really annoyed with my triple a-pillar pod, I might just got get an AEM Boost and mount it and my wide02 on the column.

Re: My Talon
 

My A-Pillar kept falling down when I had my gauges mounted there. It's like it couldn't handle the extra weight. I ended up mounting my gauges on my steering column.

Re: My Talon
 

Hey Now!!!

Re: My Talon
 

Kevin, who was it that came with you?

Re: My Talon
 

That was Matt Carlson, half owner of Primo Performance.

Re: My Talon
 

Hahahaha. Look at your sig :D

Re: My Talon
 

Wow thats over 500whp with that trap speed and weight. . .
Horsepower from ET.

Re: My Talon
 

But he's only putting down a hair more than 400.. Hmm

Re: My Talon
 

Low reading dyno...

Re: My Talon
 

True...

Re: My Talon
 

Dynos are for tuning, not for dick flopping ;)

ET with an accurate weight equalizes and applies across the board as a fair comparison.

Re: My Talon
 

why are you selling your car?

Re: My Talon
 

. . . . .

Re: My Talon
 

Got my front wheel bearings, sealls, ball joints, and outer tie rod ends. I should be doing all this front end work on Sunday. I may do a HOW TO write up! haha. I will also be doing rear calipers/rotors/pads before BIR.

Re: My Talon
 

Finally did: New front wheel bearings, in/outter seals, New ball joints, outer tie rod ends, New loaded rear calipers, rear rotors, LF axel seal. Haha, my car is getting better all the time.

Re: My Talon
 

Maybe you won't sell it ? ? ?

Re: My Talon
 

haha, I'll sell it if someone wants to buy a really nice 1G.

No one has even called to see it. boo.

Re: My Talon
 

I'll call you to come see it and take her for a joy ride! haha

Re: My Talon
 

Same here..lol

Re: My Talon
 

Putting on a Magnus SMIM right now, and decided to do some kind of wire tuck, added 2G style injector plugs, etc

Re: My Talon
 

Ooh shiney :). I mounted my coil pack today, hacked off my FIAV and sealed it up, and did a little wiring ;)

Re: My Talon
 

Maybe I missed it, but what are your IDC with the 1650's and the HX40?

Re: My Talon
 

I think somewhere in the 40-60% range, don't remember.

Re: My Talon
 

wow, thats pretty low. I could probably pull off 1200's with an HX35 then...

Re: My Talon
 

1200s are good for around 480-500awhp on E85 on my dyno.