Re: the evo 3 swap parts are coming
 

that is the plan
I will use the compleat motor and the tranny and sell the rest off

Re: the evo 3 swap parts are coming
 

I will post up all the parts that will be sold as soon as it show up on tue
the only thing that is sold as of now is the fmic and piping to my buddy kevin

Re: the evo 3 swap parts are coming
 

pics of the 5zigen stering wheel that came from japan the guy also sent me a real blitz horn button
http://i122.photobucket.com/albums/o.../evo/evo81.jpg
http://i122.photobucket.com/albums/o.../evo/evo82.jpg

Re: the evo 3 swap parts are coming
 

Funny, that is identical to my Momo wheel. Writing is even in the same place.

Re: the evo 3 swap parts are coming
 

the front clip came to day
we were safer taking this one off. we had one of are accounts come up with ther flat bed and take it off the semi and drop in the shop.
http://i122.photobucket.com/albums/o.../evo/evo83.jpg
http://i122.photobucket.com/albums/o.../evo/evo84.jpg
http://i122.photobucket.com/albums/o.../evo/evo85.jpg
http://i122.photobucket.com/albums/o.../evo/evo86.jpg

Re: the evo 3 swap parts are coming
 

this clip came with a snap-on key
http://i122.photobucket.com/albums/o.../evo/evo87.jpg
got the hks short shifter in my car
http://i122.photobucket.com/albums/o.../evo/evo88.jpg
the drive shaft just have to bolt it back together
http://i122.photobucket.com/albums/o.../evo/evo90.jpg
http://i122.photobucket.com/albums/o.../evo/evo91.jpg

Re: the evo 3 swap parts are coming
 

That key is the shit where can you get something like that.

Re: the evo 3 swap parts are coming
 

they are only sold in japan

Re: the evo 3 swap parts are coming
 

got some more done to the car and the clip
dash is in the electronic heater and a/c controler works
http://i122.photobucket.com/albums/o.../evo/evo92.jpg
http://i122.photobucket.com/albums/o.../evo/evo93.jpg
http://i122.photobucket.com/albums/o.../evo/evo94.jpg
http://i122.photobucket.com/albums/o.../evo/evo95.jpg

Re: the evo 3 swap parts are coming
 

got parts off the 2nd clip,also stared on the awd swap
http://i122.photobucket.com/albums/o.../evo/evo96.jpg
http://i122.photobucket.com/albums/o.../evo/evo97.jpg
http://i122.photobucket.com/albums/o.../evo/evo98.jpg
http://i122.photobucket.com/albums/o.../evo/evo99.jpg

Re: the evo 3 swap parts are coming
 

more of the mirage rear, gas tank is out I will be reusing it be hind the rear end,stock rear suspention is out.
http://i122.photobucket.com/albums/o...evo/evo100.jpg
http://i122.photobucket.com/albums/o...evo/evo101.jpg
http://i122.photobucket.com/albums/o...evo/evo102.jpg
http://i122.photobucket.com/albums/o...evo/evo103.jpg

Re: the evo 3 swap parts are coming
 

used the plasma cuter on the trunk floor it was all out in under 10mins
http://i122.photobucket.com/albums/o...evo/evo104.jpg
http://i122.photobucket.com/albums/o...evo/evo105.jpg

Re: the evo 3 swap parts are coming
 

got the rear end in today the back hole was there for the awd subframe. I had to drill the front hole and make a frame to frame brace to the front of the punken.
http://i122.photobucket.com/albums/o...evo/evo107.jpg
http://i122.photobucket.com/albums/o...evo/evo108.jpg
http://i122.photobucket.com/albums/o...evo/evo106.jpg
http://i122.photobucket.com/albums/o...evo/evo109.jpg

Re: the evo 3 swap parts are coming
 

cut open the frame rail to put the bolts in and tacked them in so they will be solid and I hate trying to weld rust at least it just to hold them there
http://i122.photobucket.com/albums/o...evo/evo110.jpg
http://i122.photobucket.com/albums/o...evo/evo111.jpg
http://i122.photobucket.com/albums/o...evo/evo112.jpg
http://i122.photobucket.com/albums/o...evo/evo113.jpg

Re: the evo 3 swap parts are coming
 

got some more done today. I will post up the pics as soon as I have time

Got the motor and tranny out of the clip got the tranny off and the car had a 3puck clutch and a jun flywheel so I will be putting on my jun fly and act 2100 so the wife can drive it also. Also checked out the tranny and it has a cusco lsd in it and the the rear end has a cusco lsd in it too. so just off those parts I realy got my moneys worth of the 2nd clip.

Re: the evo 3 swap parts are coming
 

pics from yesterday
first 4 got it on the ground and started to make the trunk floor we are working with the metal we have at the shop so I dont have to buy any.
http://i122.photobucket.com/albums/o...evo/evo116.jpg
http://i122.photobucket.com/albums/o...evo/evo115.jpg
http://i122.photobucket.com/albums/o...evo/evo117.jpg
http://i122.photobucket.com/albums/o...evo/evo122.jpg

Re: the evo 3 swap parts are coming
 

Sweetness. The orange really sets it off but I recommend continuing that theme over the whole car then painting "01" on the side.

Re: the evo 3 swap parts are coming
 

got the motor on the stand and took a look at it also to make sure. put a new water pump on it and a B.S. kit still have to go to mitsu to get the pump gasket and a multi layer head gasket and in stall the arp head studs. Also a pic of the front cip that will be soon cut up and be sold for a rhd swap for a 4g mirage.
http://i122.photobucket.com/albums/o...evo/evo118.jpg
http://i122.photobucket.com/albums/o...evo/evo119.jpg
http://i122.photobucket.com/albums/o...evo/evo120.jpg
http://i122.photobucket.com/albums/o...evo/evo121.jpg

Re: the evo 3 swap parts are coming
 

pic of the jun flywheel and 3 puch clutch that came out of the clip and the jun flywheel I already had and the 2100 that will be going into it.
http://i122.photobucket.com/albums/o...evo/evo114.jpg

Re: the evo 3 swap parts are coming
 

the metal is from a old battery rack that we had it is red. I will be painting the trunk with the same black I did the enging bay and make som panels for it to make it look nicer when it is done

Re: the evo 3 swap parts are coming
 

Oh, well, I'm not colorblind, so I'll blame it on technology.

Re: the evo 3 swap parts are coming
 

ya it does not look red in the pic anyway it will be black when it is painted

Re: the evo 3 swap parts are coming
 

got the new trunk floor welded in and seamsealed top and bottom and rockgarded the bottom also
http://i122.photobucket.com/albums/o...evo/evo123.jpg
http://i122.photobucket.com/albums/o...evo/evo124.jpg

Re: the evo 3 swap parts are coming
 

You should have bead rolled it for strength. :D :D

Re: the evo 3 swap parts are coming
 

Look'n good Mark!

Re: the evo 3 swap parts are coming
 

thanks
I got the engine all back togehter with the new parts on it (water pump,b.s. kit,multi layer head gasket and arp studs) motor and tranny will be going back in tomorrow. I started to make a new fuel tank sence the stock one was to big to fit behind the rear end and there is now way I will beable to get a evo III tank any thie soon.

Re: the evo 3 swap parts are coming
 

No need for an evo3 tank at all, unless you were just trying to have it be "more origional". But from your standpoint of transforming a LHD to a RHD, it doesn't matter anyway.

Re: the evo 3 swap parts are coming
 

got the motor all put back together on fri
http://i122.photobucket.com/albums/o...evo/evo125.jpg
http://i122.photobucket.com/albums/o...evo/evo126.jpg

Re: the evo 3 swap parts are coming
 

today got the tranny on it and ready to go in
http://i122.photobucket.com/albums/o...evo/evo127.jpg
http://i122.photobucket.com/albums/o...evo/evo128.jpg
http://i122.photobucket.com/albums/o...evo/evo129.jpg

Re: the evo 3 swap parts are coming
 

well motor is in and it is all hooked up and ready to go
http://i122.photobucket.com/albums/o...evo/evo130.jpg
http://i122.photobucket.com/albums/o...evo/evo131.jpg
http://i122.photobucket.com/albums/o...evo/evo132.jpg
http://i122.photobucket.com/albums/o...evo/evo133.jpg

Re: the evo 3 swap parts are coming
 

the start of my new fuel tank it is a tank for a boat the was a 18gal tank. took 4in. out of it to get it to fit perfect under the car. I cut apart the stock tank for the the pump baffel and all the mounts for the tank,sending unit,check valve and the fill and vent.
http://i122.photobucket.com/albums/o...evo/evo135.jpg

Re: the evo 3 swap parts are coming
 

Use that foam they put in fuel cells to reduce slosh. :)

Re: the evo 3 swap parts are coming
 

One of the coolest projects I've seen in a long time. Awesome.:D

Re: the evo 3 swap parts are coming
 

Looking nice man! Did you ditch the black fmic?

Re: the evo 3 swap parts are coming
 

Keep it up man, looking good! Do you have plans to put a bigger turbo setup on it sometime?

Re: the evo 3 swap parts are coming
 

thanks
I sold the black fmic and all the piping to my buddy kevin that will be going on my old 91 talon he bought from me He also bought the other evo turbo set I had from the first clip

I do have a pte 50 sitting around but I dont know if I wnat to put it on sence I would need a o2 housing a tial wastegate for it also.

Re: the evo 3 swap parts are coming
 

Looks good!

I've never seen that intake before. It has almost no plenum volume from the looks of it and the runners are shorter. I would think that would choke flow with a bigger turbo, but the shorter runners would be good for high end power. I'll be anxious to see what kind of numbers it makes. Even with a little turbo, a car that light should really move.

Re: the evo 3 swap parts are coming
 

steve,
here is the info on it stock from mitsubishi

January 1995 saw the arrival of the Evo 3- and this time the 5000 strong production run was brought up more quickly than the Evo 2. The Evo 3 looked more serious, with its new nose moulding (to channel air better to the radiator, intercooler, and brakes). New side skirts and rear corners, while the rear wing had grown again to reduce lift. Under the vented aluminium bonnet a new TDO5-16G6-7 Turbo, new exhaust system and increased compression brought another 10ps power rise, Torque output was unaltered, apart from a higher final drive ratio. Both GSR and RS still used the same 5speed gearbox. Interior tweaks were limited to a new Momo steering wheel (GSR only) and new fabric on the Evo 2 type Recaros. The specs on this vehicle were an engine size of 1997 cc, 270 bhp@6250 rpm, Torque was 228 lb ft at 3000 rpm. weight is 1260 kg (rs 1190 kg) A top speed of 149 mph and 0-60 in 4.9secs. This model still uses the same frame. (CE9A)

Re: the evo 3 swap parts are coming
 

That intake mani does look interesting. I wonder if it will flow better then the Cyclone intake mani. But eh...looking really good. Like to see more shots of that gas tank.

Re: the evo 3 swap parts are coming
 

got the drive shaft mounted yesterday and made a lic plate bracket today and worked out the lighting problems. got the city lights working (little bulb that light up the head light when running light are on) also rewired the side markers to make them runing lights and blinkers so I will now be legal. Sence it will have front running lights.
http://i122.photobucket.com/albums/o...evo/evo136.jpg
http://i122.photobucket.com/albums/o...evo/evo137.jpg
http://i122.photobucket.com/albums/o...evo/evo138.jpg