Re: Mark's Evo IX MR Winter Projects
The turbo kit has been wrapped up! All of the fabrication is complete: manifold, wastegate dump, down pipe, and lower IC piping. There are no modifications to the car, for the exception that I needed to run a Evo 5-7 radiator.
http://i412.photobucket.com/albums/p...103_183942.jpg http://i412.photobucket.com/albums/p...103_183953.jpg |
Re: Mark's Evo IX MR Winter Projects
Wow, this turned out phenomenal! Create me one! ;)
|
Re: Mark's Evo IX MR Winter Projects
A little update:
I completed the oil lines for turbo. I primed the oiling system while the timing belt was off the motor, installed a new timing belt and completed the front of the engine. Filled the trans with fluid. I installed Avid racings poly motor and trans mounts offering, they look great but the passenger side mount raises the engine up about ¼” of an inch. So I fabricated a 1/4” spacer to account for the design flaw. I cannot believe how much garbage companies produce without and verification & validation testing. Just a tiny bit of due diligence would make customers 100% happier. I installed the Magnus V5 and Boomba TB too. Next steps are to fabricate a slim line fan mount on the radiator, upper intercooler pipe, intake pipe. http://i412.photobucket.com/albums/p...105_230211.jpg |
Re: Mark's Evo IX MR Winter Projects
Hmm Magnus V5
|
Re: Mark's Evo IX MR Winter Projects
Which trans mount, the front/rear or side?
Ugh magnus IM and that huge TB...this thing is gonna freaking RIP! |
Re: Mark's Evo IX MR Winter Projects
Quote:
Motor mount on passenger side was off by a 1/4". The manifold works very good on my 1G so I was inclined to use it on the evo too. Yep this thing is going to be nasty!! |
Re: Mark's Evo IX MR Winter Projects
You do some nice work man!
|
Re: Mark's Evo IX MR Winter Projects
God that looks clean! Keep it up man, I wanna see this beast this spring :)
|
Re: Mark's Evo IX MR Winter Projects
Looking good Mark! Im jealous of your exhaust housing!!!
|
Re: Mark's Evo IX MR Winter Projects
Quote:
Quote:
Quote:
|
Re: Mark's Evo IX MR Winter Projects
Quote:
|
Re: Mark's Evo IX MR Winter Projects
Quote:
|
Re: Mark's Evo IX MR Winter Projects
Quick update, it’s getting closer! Servicing the turbo kit is going to be a pain in the ass due to the downpipe. I cannot snake it through with all of the turbo/manifold/WG/radiator components in place. I need to remove the WG then snake it up through the bottom to connect it to the turbo. There was not enough room to fit a V-band close enough down before it makes the bend to the back of the car.
http://i412.photobucket.com/albums/p...120_163844.jpg |
Re: Mark's Evo IX MR Winter Projects
That looks crazy.
|
Re: Mark's Evo IX MR Winter Projects
Quote:
Yea I know what you mean. I'm debating installing one of those electronic controlled muffler on my other Evo. I had the chance to listen to one installed on a 3" TBE on an Evo and it sound OEM! The cost is a little high but worth it in my mind. At least it gives you the option to be "normal". My only concern is road salt fucking up the actuation and electronics controlling it. |
Re: Mark's Evo IX MR Winter Projects
Any plan for a heat shield for the coolant return line ?
|
Re: Mark's Evo IX MR Winter Projects
Quote:
|
Re: Mark's Evo IX MR Winter Projects
Today I fabricated a new mount for the ethanol content sensor. I also cleaned up wiring and finalized the intake manifold. http://i412.photobucket.com/albums/p...121_153228.jpg |
Re: Mark's Evo IX MR Winter Projects
Damn, that E meter looks like a stock piece.
|
Re: Mark's Evo IX MR Winter Projects
How do you intend to utilize the ethanol content sensor with the vs 1 AEM?
|
All times are GMT -5. The time now is 09:07 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.