![]() |
Re: New Short Block
You guys think I can get away with doing a stock block and new internals? The stock block is $2500 with my discount.
|
Re: New Short Block
Can you stick a 4b11 out of another car and tell mitsu to suck it?
|
Re: New Short Block
$7500 yeow! Penny pinch man, penny pinch. I saved $$ on my motor build by doing as much myself as I felt comfortable with but it still bit me in the butt in a few spots.
I'm down with the full stage1 setup, good solid motor setup. Clean up the head. Pray none of the valves are bent--I had 6 bent IIRC and it cost me a pretty penny to fix. Send the cams AND valve tappets with to the machine shop as I wasted probably TEN days waiting for stupid new tappets and other misc delays....anyways strap it down with standard ARP headstuds torqued with a good solid torque wrench, don't forget the little oil filter screen that sits on the top of the block. More spots I saved cash on: The gasket kit--listed as $310 above idk what's in it so I just ordered peice-by-piece from mitsu (looked back at my notes for this) for $121.85: intake manifold headgasket head-to-waterpump head-to-tstat housing turbo coolant hose (mine was a little iffy) turbo drain-to-block o-ring 4x oil filter housing-to-oil cooler copper washers This leaves room for cheapo o'reily 10w30 oil for break-in, coolant, a small pile of oil filters and a fresh set of plugs. That reminds me, I have lomker's HKS spark plugs to use during your break-in if you want....no big boost on them but you can do all the vacuum pulls you want on them and then swap in a set of fresshie gapped plugs once you're ready to tune. Also I put in a fresh clutch disc in for my HDG6 to give it some extra life for something super cheap like $150. I'll post up anythign else I can think of. Also be SMART and don't go more than a few miles once you get it back together without double and maybe triple-checking ALL fluids in the car--engine oil, coolant, trans fluid, xfer case fluid, brake fluid, clutch fluid. I see people turn a blind eye to this shit...if you had a hand in assembly or not be smart and check these! |
Re: New Short Block
Quote:
|
Re: New Short Block
Quote:
|
Re: New Short Block
Mid 400's is doable with a stock shortblock, stage 1 will take you safely to 600.
|
Re: New Short Block
4g63 swap it.
|
Re: New Short Block
Kracka is making alot of power on stock motor on pump gas. stage 1 will be more then enough for what your going to throw at it.
|
Re: New Short Block
I still think throwing in a 4b11 out of something else would be dirt and they you put a bow on it and tell mitsu to suck it.
|
Re: New Short Block
Quote:
The stage 1 h-beam rods are technically not as strong but for the price difference it's way worth it, they will be plenty strong! |
Re: New Short Block
Quote:
|
Re: New Short Block
Sounds cheap to me.
I didn't see where he mentioned he can't do that, but ok. Oh my bad, turns out I should know every detail of the lease before I make suggestions. Being serious, i just think that would be funny and the cheapest way. |
Re: New Short Block
Cheapest way to do what, exactly?
|
Re: New Short Block
Put a motor in the car that works.
|
Re: New Short Block
Yes, finding a junkyard 4B11T from a 2008-2013 Evo X would probably be his cheapest alternative, but he has expressed no interest in replacing his blown up engine with another stock one.
|
Re: New Short Block
Apart from you, they do seem to blow-up pretty easily.
|
Re: New Short Block
Quote:
|
Re: New Short Block
Quote:
I agree, besides self inflicted injuries my car hasn't had any like problems that would happen to a stock car, like suspension issues or any of that crap. |
Re: New Short Block
Quote:
But apart from this random that troggy has experienced sounds like they are pretty good. high 400s is damn good too. |
Re: New Short Block
Word. Come down to Texas I'll we attempt to get BBQ again!
|
| All times are GMT -5. The time now is 12:20 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.