slowbubblecar
03-12-2015, 09:04 AM
***Price drop to $1,000 if gone by the end of the week***
Price: Asking $1,200/BO and it is
Location:Minnetonka, MN
Condition: Fair
Purchased the vehicle from a member a few years ago with the intent of pulling the parts out to put in another vehicle and junking the body, but I didn't have time to mess with it and it is just sitting at one of my houses now.
Below is a list of the mods:
MAP Performance stage 1 2.0 shortblock - 6 Bolt (less than 1,000 miles, but sat the last several years)
-Hot tank/boil block
-Polished crank
-Balanced
-ACL Race series main and rod bearings
-Overbore with torque plate
-Fully decked
-Mahle 8.5:1 Forged pistons
-Eagle rods
-Balance shafts eliminated
-New front case: Oil pump, oil pump drive gear, oil pump driven gear
Head:
-Used good condition cylinder head that was rebuilt as well
-Brian crower valve springs and retainers
-new exhause and intake oil seals
-5 angle valve job
-16 Gallon Fuel cell
-280 fuel pump
-255 inline fuel pump
-Adjustable Fuel pressure regulator
-Small 16g
-Pacesetter tubular manifold
-Fidanza 3.2 Clutch and pressure plate/throwout bearing
-boost and A/F gauges on A pillar
-Adjustable throttle cable
-gates racing timing belt
The vehicle does not have FMIC, exhaust, BOV, intake and likely other parts. It is as it was when I purchased it.
Below is a link so you can see a few additional pictures and a project thread from a prior owner. I purchased it from the person who bought it from this guy. The bumper is off of it, the hood is black and several interior items are missing.
http://www.mitsustyle.com/forums/showthread.php?t=25945&highlight=laser
Selling the car as a part car with no title. It is possible to get it titled, but it would take a little time/work to complete the process and I didn't think it would be worth the hassle.
James
Price: Asking $1,200/BO and it is
Location:Minnetonka, MN
Condition: Fair
Purchased the vehicle from a member a few years ago with the intent of pulling the parts out to put in another vehicle and junking the body, but I didn't have time to mess with it and it is just sitting at one of my houses now.
Below is a list of the mods:
MAP Performance stage 1 2.0 shortblock - 6 Bolt (less than 1,000 miles, but sat the last several years)
-Hot tank/boil block
-Polished crank
-Balanced
-ACL Race series main and rod bearings
-Overbore with torque plate
-Fully decked
-Mahle 8.5:1 Forged pistons
-Eagle rods
-Balance shafts eliminated
-New front case: Oil pump, oil pump drive gear, oil pump driven gear
Head:
-Used good condition cylinder head that was rebuilt as well
-Brian crower valve springs and retainers
-new exhause and intake oil seals
-5 angle valve job
-16 Gallon Fuel cell
-280 fuel pump
-255 inline fuel pump
-Adjustable Fuel pressure regulator
-Small 16g
-Pacesetter tubular manifold
-Fidanza 3.2 Clutch and pressure plate/throwout bearing
-boost and A/F gauges on A pillar
-Adjustable throttle cable
-gates racing timing belt
The vehicle does not have FMIC, exhaust, BOV, intake and likely other parts. It is as it was when I purchased it.
Below is a link so you can see a few additional pictures and a project thread from a prior owner. I purchased it from the person who bought it from this guy. The bumper is off of it, the hood is black and several interior items are missing.
http://www.mitsustyle.com/forums/showthread.php?t=25945&highlight=laser
Selling the car as a part car with no title. It is possible to get it titled, but it would take a little time/work to complete the process and I didn't think it would be worth the hassle.
James