Timing Belt Questions

[SpicyOrange]

Ok I want to get my basket case back together and I want some suggestions on what I should replace when I'm in there replacing the timing belt, my car only has 60000 miles on it, And is there any sites on here that could guide me throught the steps so I don't forget anything, I've never dealt with DOHC gears yet, but I know I could handle it. Thanks DSMStyle

Nick

[Goat Blower]

At a minimum I'd replace the t-belt, balance shaft belt water pump and tensioner. While you're in there, check the idler pulley and tensioner pulley for any play, they should spin smoothly with no slop. Also check the crank sensor for damage just in case. There's alot of info out there on doing this. Start with www.vfaq.com.

[timwakefieldjr]

I am gonna have to agree with Goat Blower. While you are there take the time to replace the tensioner and balance shafts. It also always good to double check the simple stuff like motor mounts as you are peaking into the bay. Good luck and make sure to post and tell us how it went.

-Tim

[Enes]

i did the timing belt myself.. well honestly.. i'm no mechanic... i tought it would be good experience.. well in whole truth. it was.. but guess what else hapend? i over tightened the belt and now it needs replacing again 15k miles later.. and this time i'm buying everything new again...

it sux.. but i'll just make the 7 bolt last this year hopefully.. but for that i'll have to let someone else do the timing belt this time :(

-E

[Halon]

how can you tell if its over tightened?

[Enes]

the belt shows excessive wear on the side as well as you can see and feel the teeth come thru etc etc.

-E

[Halon]

how about when you're doing the actual install. Is there a way to check if it's at the correct tension before you see it wearing and realise it was too tight?

[A//// Guy]

The only way you can tell if its over tightened is check the gap in the tensioner after you finish the install... There is a limit in how far the pin pushes in the tensioner and its only supposed to be gapped so much. Check out a manual and it will tell you. VFAQ also has some nice Tbelt steps and info.

Ive done my tbelt a few times and you definetly need the right tools including guage for the tensioner unless you use the factory bolt that releases the tension. I just took it off and used a vise. After a couple times its cake but the first is the worst. Ive had to take it all apart once right after I did an install becuase the balance shaft spun around the wrong way and it looked lined up but it wasnt. -Terrible shaking comes from that.

[Halon]

ya i know how to check all that, but the tension im not sure of. I know to take out the tensioner, then use a vice to press it and alling the pin holes. But I guess that's where i forget what goes on after that. My memory is bad sometimes. It's one of those things I've been told so many times, yet I always forget.

[Halon]

ok, my memory kicked back in. In case anyone is like me and forgets, here's the way I was taught to setup and check the correct tension...
-Remove the hydraulic tensioner and compress it with vice grips
-When compressing, alling the holes in the tensioner
-Once holes are alligned, stick a small allen wrench through all 3 holes.
-Reinstall the hydraulic tensioner
-Once the t-belt is installed and all timing marks are correct, make sure the bolt on the tensioner pulley is loose.
-Pry on the tensioner pulley to tighten the belt, then tighten the bolt in the center of the pulley.
-If the tension is set correct, you should be able to slide the allen wrench out fairly easily, and slide it back in through all 3 holes fairly easily
-If the allen wrench does not slide in and out easily, then you have it too tight or too loose.

That's how I was taught, if anyone see's something wrong with that process then please chime because if i'm doing it wrong, I sure would like ti know.