PDA

View Full Version : New from ND

Pages : [1] 2
Perkul8r
05-28-2010, 11:29 PM
Whats up everyone. I have been wandering this site quite a bit and just now finally got a mitsu. Kinda. lol. Its a 1990 Laser RS turbo. It does need some work, but thats why i got it, and for the price i couldn't let it pass by. Well, here it is.

http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0112.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0113.jpg

http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0114.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0118.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0119.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0120.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0121.jpg
http://i665.photobucket.com/albums/vv14/Perkul8r/Plymouth%20Laser/SAM_0122.jpg
GG_9_SE
05-28-2010, 11:37 PM
side exit exhaust ftw! Welcome to the site
Perkul8r
05-28-2010, 11:44 PM
Thanks.
Ya the previous owner did that cause he was racing 1/8th mile with it. Its a 3 inch megan downpipe to 3 inch pipe with a dynamax race pack. I have never heard it, but it should sound good.
Nartanian
05-28-2010, 11:56 PM
Very nice. What are your plans for it?
turbotalon1g
05-29-2010, 05:18 AM
Nice, welcome and that isn't in an impound lot in the first pic?
scheides
05-29-2010, 08:17 AM
What do you mean kinda? You got a 4G63 in that thing son, represent!

What's the condition of this thing, does it run? Looks pretty stock, which is a great place to start. Good luck getting it up and rockin!
98gstaherns
05-29-2010, 08:56 AM
Welcome! You know its a DSM when it comes with a tow strap! lol Good luck with it!
Constant_Project21
05-29-2010, 12:14 PM
Welcome to the site, whats sprayed on that manifold and o2 housing?
Perkul8r
05-29-2010, 06:38 PM
First off, no its not an impound lot. lol. That was at the shop were it was sitting.

The car is pretty stock except the exhaust. The previous owner was running an aftermarket BC on it and thats about it.

My plans are to figure out what happened to the motor. So ya, it dont run. lol. The previous owner said that the balance shaft belt went out on it and when they tried to turn it over by hand that it wouldn't go. So he said the piston might have slapped the head. But the timing belt is tight. There is a groove on the timing belt on the very inside edge of it. So i am gonna tear down the front of the engine and see if i can find something that might be jamming it up.
Perkul8r
05-30-2010, 11:33 PM
Well torn into the car today. The timing belt had teeth stripped off it. So bent valves. Great. So now i am looking for a new head. Or maybe a Cyclone motor. Not sure yet.