TSI_G_FORCE
08-12-2008, 12:31 PM
*RED 92 EAGLE TALON AWD ROLLING SHELL WITH FULL INTERIOR AND 4 BOLT REAR END - $600.00 (MISSING FRONT BUMPER, NO RUST)
*BUSCHER AWD RACING EXHAUST (FULL 3" EXHAUST SYSTEM) - $500.00 DOWN PIPE TAPPED FOR AEM WIDEBAND.
*BUSCHER RACING FRONT MOUNT INTERCOOLER KIT - $600.00
*GREDDY PROFEC B SPEC 2 ELECTRONIC BOOST CONTROLLER - $250.00 COMES WITH EVERYTHING READY TO INSTALL.
*MAF TRANSLATOR - $150.00
*22 SPLINE REBUILT TRANNY WITH APPROXIMATELY 5K MILES (SHIFTS LIKE BUTTER) - $600.00
*BUSCHER 20G TURBO (SOME SHAFT PLAY) - $400.00
*BRAND HAFE PERFORMANCE CAST S.S. 7CM DSM MANIFOLD W/ 38MM WG PREVISION - $250.00
*HOLLEY 660CC INJECTORS - $175.00
*STOCK REBUILT HEAD WITH 3G LIFTERS AND BRIAN CROWER 272'S - $600.00 THE CAMS ARE ALREADY INSTALLED ON THE HEAD AND READY TO BOLT ON. I HAVE RAN THE HEAD AND CAMS FOR ONLY ABOUT 500 MILES. NO BS. HERE'S A RUNDOWN ON WHAT WAS DONE ON THE HEAD JOB: Head was thoroughly cleaned and inspected. Pressure tested to ensure no cracks or leaks. Guide work performed and replaced with new guides. Valve job performed on Serdi or Sunnen machine. CBN milled to ensure straightness within .0015" and correct finish. All machine work performed on the latest state of the art equipment. All parts were thoroughly cleaned and inspected before assembly. Head was assembled with 16 new valve seals, 8 brand new intake valves and 8 brand new exhaust valves. Head was assembled with new valve seals.
EMAIL: beeandmailee@hotmail.com
PHONE: 651-263-1979 (BEE)
*BUSCHER AWD RACING EXHAUST (FULL 3" EXHAUST SYSTEM) - $500.00 DOWN PIPE TAPPED FOR AEM WIDEBAND.
*BUSCHER RACING FRONT MOUNT INTERCOOLER KIT - $600.00
*GREDDY PROFEC B SPEC 2 ELECTRONIC BOOST CONTROLLER - $250.00 COMES WITH EVERYTHING READY TO INSTALL.
*MAF TRANSLATOR - $150.00
*22 SPLINE REBUILT TRANNY WITH APPROXIMATELY 5K MILES (SHIFTS LIKE BUTTER) - $600.00
*BUSCHER 20G TURBO (SOME SHAFT PLAY) - $400.00
*BRAND HAFE PERFORMANCE CAST S.S. 7CM DSM MANIFOLD W/ 38MM WG PREVISION - $250.00
*HOLLEY 660CC INJECTORS - $175.00
*STOCK REBUILT HEAD WITH 3G LIFTERS AND BRIAN CROWER 272'S - $600.00 THE CAMS ARE ALREADY INSTALLED ON THE HEAD AND READY TO BOLT ON. I HAVE RAN THE HEAD AND CAMS FOR ONLY ABOUT 500 MILES. NO BS. HERE'S A RUNDOWN ON WHAT WAS DONE ON THE HEAD JOB: Head was thoroughly cleaned and inspected. Pressure tested to ensure no cracks or leaks. Guide work performed and replaced with new guides. Valve job performed on Serdi or Sunnen machine. CBN milled to ensure straightness within .0015" and correct finish. All machine work performed on the latest state of the art equipment. All parts were thoroughly cleaned and inspected before assembly. Head was assembled with 16 new valve seals, 8 brand new intake valves and 8 brand new exhaust valves. Head was assembled with new valve seals.
EMAIL: beeandmailee@hotmail.com
PHONE: 651-263-1979 (BEE)