Feeler:FEELER: 91 GVR4 #1062 full race build $10,000.00 OBO

[Pushit2.0]

I was building this car to run 8s at some point. It would only take a few weekends of work to finish this car. The body is in fare shape a little rust around the window, a few dings here and there. The interior is stripped right now, and has a 8point roll cage in it(would be certified for an 8.50@150mph. I have the full interior and a lot of extras. I also did not plan on running any kind of lights, head lights or tail lights so you would need to wire those back in, this was going to be a series race car. The chassis has just over 100k on it and here is the VIN: JA3CX56U0MZ010883 and I would also part the car out if that would work better. Here is the link to the gallery with most of the pics:
http://lseperformance.com/gallery/main.php?g2_itemId=3231
I will get a few more pics up of the rest of the car tonight.

Here is the new list of for sale items.

LSE stage 4 short block (2.0L still), 40 over 9.25:1 Weisco pistons, Crower rods, ARP mains, LSE main cap pins, no oil squirters, new TB side w/ Greddy timing belt
-LSE stage 6 head, race port head, 2mm over I/E SS valves, Crower 415s, Crower cam gearsn
-Cometic HP head gasket
-A1 L-19 head studs
Running engine $5000 obo

-ACT street light flywheel $120 obo

-Custom south bend race only clutch (single disk design) $300 obo

-3bolt ring/pinion 4bolt rear end combo $250 obo

-water to air IC setup, with a custom side mount heat exchanger, intake air temp was only 10deg above outside air temp at 47psi..... with no ice in the water tank. $650 obo

-AEM EMS for tuning, AEM 5bar MAP, GM AIT sensor, 93 CAS (pending sale)

-Full MSD ignition, DIS 2, GM twin post coils, MSD wires $450 obo

http://img443.imageshack.us/my.php?image=dsc02371it9.jpg
http://img443.imageshack.us/my.php?image=dsc02370uq8.jpg
http://img443.imageshack.us/img443/5720/dsc02369bk9.th.jpg

The hole car as it sits: $7,000 OBO

I just do not have the budget to finish and maintain the car, I wish I did, but not right now. Email: GalantVR41062@yahoo.com, PM, Phone:7634254340. Thanks for looking!

~John

[qualmq]

If you end up parting out your car, I will take that ignition system off your hands. You know how bad the cert needs it.

~Mark Q.

[Pushit2.0]

Can a MOD change the title and adjust the price, thank you. $10,000 OBO. Call my cell phone thanks.

~John

[Super Bleeder!!]

Holy shit that is a bargain. It saddens me :(

[DSM_421]

Yea, hope it goes locally and gets finished.

I want to sex this thing up.

[craig]

wouldnt mind the intake man and tb if it gets parted also maybe the ext man

[Swifty1638]

john, call and leave me a message on the turbo and manifold setup..you know I want the motor too, but yea..Otherwise, I'll call later this week bout welding my cage in and making the upper ic pipe..

-A. Swift

[Pushit2.0]

I might part out a few things, PM me with what you want. The Intake manifold I want to test back to back against a leading design, AMS or Magnus if possible.

~John

[Pushit2.0]

Update

~John

[Pushit2.0]

Update again, looking to sell the rest of the fuel setup, clutch, water to air IC, and the rear end, PM with offers.

~John